We have RJ30ib Controller that we are redeploying. It use to run via the Style commands but we are changing it to Other, and production start method is UOP. I have selected my MASTER program as the starting program under %shell_wrk.$cust_name and I can jog the robot through the job but when I try to start the job in Auto the robot does not run. I am Holding UOP UI 1,2,3, and 8 on. I pulse UI 5 for .75 sec, and pulse UI 6 on. The program still does not run with these variables set. What am I missing? I am mostly familiar with Motoman Robots so Fanuc is a weak point.
Program Start Method
-
BananaMan77777777 -
March 13, 2023 at 8:05 PM -
Thread is marked as Resolved.
-
- Go to Best Answer
-
95devils
March 13, 2023 at 8:08 PM Approved the thread. -
Check in MENU -> SYSTEM -> Config what do you have for „START for CONTINUE” - TRUE or FALSE?
In genaral UI[6] is used to start the PAUSED program.
When you want to start a program which is not PAUSED, from the 1st line, use UI[18].
-
Check if Remote/Local setup under MENU > System > Config is set to Remote.
-
Remote is selected in System Config
-
Check in SETUP what do you have for „START for CONTINUE” - TRUE or FALSE?
In genaral UI[6] is used to start the PAUSED program.
When you want to start a program which is not PAUSED, from the 1st line, use UI[18].
Start for continue only is set to FALSE
-
Also check if the system variable $RMT_MASTER is set to 0. Also verify the points suggested by neighbour1. Are there any errors or messages displayed when trying to start the program?
-
Start for continue only is set to FALSE
Following the manual:
1. If START for CONTINUE only on the system setting menu is set to FALSE, the currently selected program is started from the current line. A temporarily stopped program is also started. (Standard setting)
2. If START for CONTINUE only on the system setting menu is set to TRUE, any temporarily stopped
program is started. This signal is ignored when there is no temporarily stopped program.
Try to use UI[18].
-
Following the manual:
1. If START for CONTINUE only on the system setting menu is set to FALSE, the currently selected program is started from the current line. A temporarily stopped program is also started. (Standard setting)
2. If START for CONTINUE only on the system setting menu is set to TRUE, any temporarily stopped
program is started. This signal is ignored when there is no temporarily stopped program.
Try to use UI[18].
We tried using UI[18] before switching to UI[6] and had the same results.
-
Check also:
1. TP = OFF?
2. AUTO is selected (operator's panel key)?
-
How do you control the UOP signals? Discrete wiring or via PLC and a fieldbus protocol? Did you already check if the mapping of your UOP signals is correct?
-
How do you control the UOP signals? Discrete wiring or via PLC and a fieldbus protocol? Did you already check if the mapping of your UOP signals is correct?
RMT_MASTER is set to 0.
TP is off.
Pendant says it's in Auto.
Controlling UOPs over Ethernet with a PLC. I can see the UOPs change states on the pendant from the PLC
-
What about Enable UI signals = TRUE or FALSE (set it to TRUE).
It's also hidden in Config (MENU -> SYSTEM -> Config).
-
What about Enable UI signals = TRUE or FALSE (set it to TRUE).
It's also hidden in Config (MENU -> SYSTEM -> Config).
Enable UI signals = True
-
Sounds like everything is OK
-
Don't you have any spelling mistake in the program name $shell_wrk.$cust_name?
Does the start program exist? -> press SELECT and chect if it's there.
-
Is there a motion group blocked by another program (left in PAUSED mode)?
Press FCTN -> Abort all.
-
Don't you have any spelling mistake in the program name $shell_wrk.$cust_name?
Does the start program exist? -> press SELECT and chect if it's there.
Start program was selected through the options menu from the tp list.
I have done the abort all and nothing changes.
-
Are there any errors or messages displayed when trying to start the program?
-
[…]
No errors or Alarms are present
-
I want to leave this update as I may have found a fix but will update tomorrow on if it works.
ThreadUnable to Change Program Select Mode
I am having some issues trying to change our Fanuc LR Mate 200iD's program select mode. It came to us in the PNS select mode, and I would like to use the OTHER mode to simplify things.
However, when I try to change the mode and cycle power by shutting the main power off and then on, it simply resets back to the PNS mode of program selection.
Can any one help me out with this one?
Thanks!ACalverley2March 7, 2021 at 4:00 PM -