1. Home
    1. Dashboard
    2. Search
  2. Forum
    1. Unresolved Threads
    2. Members
      1. Recent Activities
      2. Users Online
      3. Team Members
      4. Search Members
      5. Trophys
  3. Articles
  4. Blog
  5. Videos
  6. Jobs
  7. Shop
    1. Orders
  • Login or register
  • Search
This Thread
  • Everywhere
  • This Thread
  • This Forum
  • Articles
  • Pages
  • Forum
  • Blog Articles
  • Products
  • More Options
  1. Robotforum - Support and discussion community for industrial robots and cobots
  2. Forum
  3. Industrial Robot Support and Discussion Center
  4. KUKA Robot Forum
Your browser does not support videos RoboDK Software for simulation and programming
Visit our Mainsponsor
IRBCAM
Robotics Channel
Robotics Training
Advertise in robotics
Sponsored Ads

X11 help

  • vvelikov
  • April 28, 2022 at 2:28 PM
  • Thread is Unresolved
  • Online
    vvelikov
    Reactions Received
    6
    Trophies
    4
    Posts
    484
    • April 28, 2022 at 2:28 PM
    • #1

    Hello,

    I am trying to run a KR16-2 KSS 5.6.10 robot with KRC2ed05 PC
    I did the X11 from the forum files - standard KRC2 type and the robot is moving fine in manual mode (T1 and T2) but cannot be moved in AUT - the I stays red
    X11 doesn't have pins on numbers 37 and 40

    The KSS is clean install, so all in Automatic external is at default settings.

    I am attaching two pages with the description of the X11 of this particular robot as i suspect that there may be is something else need to be done on the X11


    I swapped the PC and the KCP with no luck

    Any advise appreciated!

    Files

    X11_1.pdf 896.74 kB – 90 Downloads X11_2.pdf 801.46 kB – 63 Downloads
  • panic mode
    Reactions Received
    1,267
    Trophies
    11
    Posts
    13,033
    • April 28, 2022 at 2:52 PM
    • #2

    you do not need to connect 37 and 40. that is only for KRC1 (safety relays common...).

    if you look at my X11 jumper plug connection diagram in download section, it is clearly stated that this is for KRC1 only. when one is making test jumper plug it is convenient to add that connection so that plug can be used on both KRC2 and KRC1 but obviously KRC2 does not need it.

    1) read pinned topic: READ FIRST...

    2) if you have an issue with robot, post question in the correct forum section... do NOT contact me directly

    3) read 1 and 2

  • Online
    vvelikov
    Reactions Received
    6
    Trophies
    4
    Posts
    484
    • April 28, 2022 at 4:17 PM
    • #3

    Thanks for replying!

    I did not connect 37-40 just used the one i am attaching here.

    But something stops the robot to move in automatic mode.

    Images

    • X11.jpg
      • 78.95 kB
      • 589 × 1,200
      • 57
  • panic mode
    Reactions Received
    1,267
    Trophies
    11
    Posts
    13,033
    • April 28, 2022 at 4:39 PM
    • #4

    can you be more specific?

    that is one way to wire X11 but ... which connections did you actually make? and did you check them? how?

    what are the messages?

    what are the states of signals grouped in AutoExternal interface?


    if robot can move in T1 then most of the safety circuit should be ok.

    the only difference in auto modes is that user safety must be closed and acknowledged. so that would be the things to check.

    1) read pinned topic: READ FIRST...

    2) if you have an issue with robot, post question in the correct forum section... do NOT contact me directly

    3) read 1 and 2

  • Online
    vvelikov
    Reactions Received
    6
    Trophies
    4
    Posts
    484
    • April 28, 2022 at 5:07 PM
    • #5

    No messages at all :frowning_face: it seems all is good... i recall may be i saw "safety circuit not ready" but it was cleared afterwards and didn't came up. Also i did some cold starts without any warnings etc...

    I will check the AutoExternal signals and write here

    The connections - checked triple with multimeter (and more):
    1-2
    3-4
    5-6
    7-8
    19-20
    21-22
    23-24
    25-26
    38-50
    39-51
    41-42
    43-44
    107-89
    106-88

    I have nothing at 71, 108, 70, 54

  • Online
    SkyeFire
    Reactions Received
    1,040
    Trophies
    12
    Posts
    9,380
    • April 29, 2022 at 2:07 PM
    • #6

    You're trying to use AUT mode, correct?

    How are $DRIVES_OFF and $MOVE_ENABLE configured?

    Long shot, but... can you swap the KCP for another one? It might just be that the drives-on button on the KCP isn't working.

  • Online
    vvelikov
    Reactions Received
    6
    Trophies
    4
    Posts
    484
    • April 29, 2022 at 2:50 PM
    • #7

    Yes, AUT mode.
    Already swapped the KCP - nothing changed :frowning_face:

    $DRIVES_OFF and $MOVE_ENABLE are as by default - 1025

    If you take a look at the PDFs you will notice that there are some more pins:

Advertising from our partners

IRBCAM
Robotics Channel
Robotics Training
Advertise in robotics
Advertise in Robotics
Advertise in Robotics

Job Postings

  • Anyware Robotics is hiring!

    yzhou377 February 23, 2025 at 4:54 AM
  • How to see your Job Posting (search or recruit) here in Robot-Forum.com

    Werner Hampel November 18, 2021 at 3:44 PM
Your browser does not support videos RoboDK Software for simulation and programming

Tag Cloud

  • abb
  • Backup
  • calibration
  • Communication
  • CRX
  • DCS
  • dx100
  • dx200
  • error
  • Ethernet
  • Ethernet IP
  • external axis
  • Fanuc
  • help
  • hmi
  • I/O
  • irc5
  • IRVIsion
  • karel
  • kawasaki
  • KRC2
  • KRC4
  • KRC 4
  • KRL
  • KUKA
  • motoman
  • Offset
  • PLC
  • PROFINET
  • Program
  • Programming
  • RAPID
  • robodk
  • roboguide
  • robot
  • robotstudio
  • RSI
  • safety
  • Siemens
  • simulation
  • SPEED
  • staubli
  • tcp
  • TCP/IP
  • teach pendant
  • vision
  • Welding
  • workvisual
  • yaskawa
  • YRC1000

Thread Tag Cloud

  • abb
  • Backup
  • calibration
  • Communication
  • CRX
  • DCS
  • dx100
  • dx200
  • error
  • Ethernet
  • Ethernet IP
  • external axis
  • Fanuc
  • help
  • hmi
  • I/O
  • irc5
  • IRVIsion
  • karel
  • kawasaki
  • KRC2
  • KRC4
  • KRC 4
  • KRL
  • KUKA
  • motoman
  • Offset
  • PLC
  • PROFINET
  • Program
  • Programming
  • RAPID
  • robodk
  • roboguide
  • robot
  • robotstudio
  • RSI
  • safety
  • Siemens
  • simulation
  • SPEED
  • staubli
  • tcp
  • TCP/IP
  • teach pendant
  • vision
  • Welding
  • workvisual
  • yaskawa
  • YRC1000

Similar Threads

  • KRC4 8.6.5 Ethernet/IP 4.1.3 With Schneider M241 PLC communication

    • Skarin
    • March 10, 2022 at 9:44 PM
    • KUKA Robot Forum
  • Kuka KRC I/O greyed out and DeviceNet error

    • soundwawe
    • April 3, 2022 at 10:53 PM
    • KUKA Robot Forum
  • KCP Cable Kuka KRC2

    • dudz
    • February 26, 2022 at 2:18 PM
    • KUKA Robot Forum
  • ROBOT KUKA WITH MODULE ETHERNET KRL

    • Alexis Moctezuma
    • April 27, 2022 at 4:26 AM
    • KUKA Robot Forum
  • Clicking noise on A4 to A6 axis KR6

    • evo85210
    • April 13, 2022 at 11:27 AM
    • KUKA Robot Forum
  • When loading the KRC2ED05 robot cabinet, a message appears

    • Ryno
    • April 22, 2022 at 7:32 PM
    • KUKA Robot Forum
  • Error/Skewed Data during Dynamic Force Data Analysis

    • d3vS
    • April 19, 2022 at 3:57 AM
    • KUKA Robot Forum
  • Smooth change case”s in switch.

    • Sh1ox
    • April 13, 2022 at 6:06 PM
    • KUKA Robot Forum
  1. Privacy Policy
  2. Legal Notice
Powered by WoltLab Suite™
As a registered Member:
* You will see no Google advertising
* You can translate posts into your local language
* You can ask questions or help the community with your knowledge
* You can thank the authors for their help
* You can receive notifications of replies or new topics on request
* We do not sell your data - we promise

JOIN OUR GREAT ROBOTICS COMMUNITY.
Don’t have an account yet? Register yourself now and be a part of our community!
Register Yourself Lost Password
Robotforum - Support and discussion community for industrial robots and cobots in the WSC-Connect App on Google Play
Robotforum - Support and discussion community for industrial robots and cobots in the WSC-Connect App on the App Store
Download