R-j2 error installing

DbdInvasion · April 22, 2021 at 11:44 PM

Ok so we received a used R-J2 100 arcmate. Went through and worked out all the errors. Went and backed up the controller.

Still having some problems so was wanting to load our other 100 rj2 robots info quick to see if some sys variables were the cause.

Ran

Install/run/frominit

(Worked in the past, might not be the fastest but has worked for us since we have the original fanuc software)

But after it cleared chip 2 and was wanting to read the system1.ldc file I get a port timeout press 1 or 0 ect.

Also this controllers EPMON doesn't seem to have a restore button.

Confused on what to do next.

Skooter · April 23, 2021 at 1:11 AM

Install/Run/FROMINIT.CF is the procedure for loading software, not a backup. Initializing the FROM just deleted the software, it needs to be reloaded. The system1.ldc file it is looking for is on the APP1 disk of the software. Hopefully you have the software and the backup you wisely took is good.

DbdInvasion · April 23, 2021 at 2:05 PM

Well I had backed up already and was trying to restore it to a different ones software to see if it took out the bugs.

And when trying to load the new software and look for the system1.ldc off the APP1 disk (have kfloppy running through r-233 cable/compatible computer) but I time out for a port error

Skooter · April 23, 2021 at 2:35 PM

Verify Kfloppy on the other robot by doing a directory of the APP1 and see if it reads. Make sure logging is off so you don't write a log file to the directory.

DbdInvasion · May 4, 2021 at 3:54 PM

Figured out what was going on.. My EPMON has a older version then the current one that i had the updates for.. switched the MCB with a known good one with the updated EPMON Chip and am able to move forward..

But now after i was able to get the restore option and everything.

While recovering it wants to send over the -BCKEDT-.TP i get a message "This program is being edited" and has been like this for over 30 minutes now. Is this normal? going to wait for about an hour to see since sometimes it takes a while to do anything with kfloppy so shrug.. any thoughts?

HawkME · May 4, 2021 at 5:42 PM

You don't need that file. See if you can delete it.

Skooter · May 4, 2021 at 6:04 PM

I always skip loading the background edit files when this appears.

CaioDiniz · April 19, 2022 at 3:47 PM

good morning Skooter , can i restore controller via ethernet?

Skooter · April 20, 2022 at 3:02 AM

R-J2 doesn't have ethernet. RS232 or if you are lucky, it has the PCMCIA Interface & software option.

pdl · April 20, 2022 at 4:48 AM

And if you're not lucky, search the forum for advice on using KFLOPPY. KFLOPPY can work with a USB to UART serial adapter, but it is easiest to get it to run with a native windows XP machine with a real serial port.

In the end, bits are bits. KFLOPPY will work, it just may take some time to get it configured properly. Even on new robots, I would always use a compact flash card via a PCMCIA adapter if that option is available.

CaioDiniz · April 20, 2022 at 9:53 PM

on my r-j2 panel it has the RJ45 input on the CPU. In some manuals it says that it is possible to transfer files through FTP, it just doesn't explain how to do it.

Skooter · April 21, 2022 at 1:02 AM

That's new to me. What is the part number of the CPU? It should start with A16B-

Or you could post a picture.

pdl · April 21, 2022 at 4:31 AM

What options are listed under SETUP > HOST COMM?

A screenshot would tell volumes.

kluk-kluk · April 21, 2022 at 8:33 AM

The part number for the RJ-2 ethernetcard is A20b-8001-0120.

However, to get it working is not easy, so I think kfloppy is the way to go.

Skooter · April 21, 2022 at 4:24 PM

I believe that connection on the RIO card is for communication with the Allen Bradley PLC and doesn't have access to file management.

I show the manual # for the board as MARO2AB4405801E.

kluk-kluk · April 22, 2022 at 12:01 PM

I am afraid I don't have that manual.

We bought the robots having these A20b-8001-0120 cards second hand, and when we collected them, they were all connected to a networkswith (or hub) with no PLC in sight.

So, while i am not for 100% sure, I do think file management was possible.

Unfortunately I can't reach the former owner to ask.

pdl · April 22, 2022 at 8:52 PM

A picture of the Host Comm screen would really help answer this question.

R-j2 error installing

Advertising from our partners

How to see your Job Posting (search or recruit) here in Robot-Forum.com

Similar Threads

Fanuc roboguide installation error

Fanuc R30iB loses image at power loss.

KR C4 SmartHMI Unhandled Exception

error StartKRC.exe

Fanuc 30iA INTP-311 error after installing Ethernet/IP option

ERROR 07003 ABB

WeldPRO Error

Running Roboguide on Windows 10

Tags