Stäubli & Bosch Robot Forum
The very fast and highly accurate Swiss robot speaks many languages.
Download or ask for Freeware, Manuals and other Stuff about Stäubli Robots
- Threads
- 10
- Posts
- 26
- Last Posts
-
-
-
How to read a virtual signal from a tool in SRS2019 (eg.: "diPartDetected")? 6
- mil3k
December 13, 2023 at 10:48 AM
- mil3k
December 19, 2023 at 1:12 PM
-
- Replies
- 6
- Views
- 1.8k
6
-
-
-
-
CS8C error codes - U and in ARPS 12v2 not showing 1
- Sarath Kumar
December 6, 2023 at 7:29 AM
- Sarath Kumar
December 7, 2023 at 2:03 PM
-
- Replies
- 1
- Views
- 1.4k
1
-
-
-
-
TS2-40 Cube area 2
- samu1995
December 1, 2023 at 5:04 PM
- samu1995
January 16, 2024 at 9:28 AM
-
- Replies
- 2
- Views
- 2.3k
2
-
-
-
-
Staubli J1203 Connectors 6
- aknezevi.proton
November 22, 2023 at 2:55 PM
- aknezevi.proton
December 4, 2023 at 9:10 AM
-
- Replies
- 6
- Views
- 1.7k
6
-
-
-
-
Password staubli maintenance (https://ip_adress/mobile.html) 3
- samu1995
November 21, 2023 at 2:14 PM
- samu1995
November 24, 2023 at 8:16 AM
-
- Replies
- 3
- Views
- 1.5k
3
-
-
-
-
CS8C configure profibus dio in iomap.cf 9
- aknezevi.proton
November 21, 2023 at 8:20 AM
- aknezevi.proton
December 4, 2023 at 9:35 AM
-
- Replies
- 9
- Views
- 1.7k
9
-
-
-
-
Issues connecting with PC and uploading programs to cs8c controller 3
- JosuGaztelu
November 20, 2023 at 8:33 AM
- JosuGaztelu
November 29, 2023 at 2:43 PM
-
- Replies
- 3
- Views
- 1.3k
3
-
-
-
-
Cs8c cannot detect USB and safety error System event SAFETY-ThermoOpened.(0x1738) 1
- JosuGaztelu
November 15, 2023 at 9:35 AM
- JosuGaztelu
November 16, 2023 at 11:55 AM
-
- Replies
- 1
- Views
- 886
1
-
-
-
-
Staubli cs8 controller startup application without MCP 1
- Dominik Wenesz
November 9, 2023 at 3:38 PM
- Dominik Wenesz
November 9, 2023 at 7:04 PM
-
- Replies
- 1
- Views
- 757
1
-
-
-
-
DSI board not referenced fault 3
- haydenfscott
November 5, 2023 at 11:43 PM
- haydenfscott
April 2, 2024 at 3:37 PM
-
- Replies
- 3
- Views
- 2k
3
-
-
-
-
How can I calculate the tool (x and y) of a Staubli ts2-40 4-axis robot? (No 6 axes calculation) 3
- samu1995
November 1, 2023 at 10:56 PM
- samu1995
November 4, 2023 at 6:30 PM
-
- Replies
- 3
- Views
- 712
3
-
-
-
-
Staubli TX90 CS8C Controller
- DeBussy
October 26, 2023 at 3:22 AM
- DeBussy
October 26, 2023 at 3:22 AM
-
- Replies
- 0
- Views
- 551
-
-
-
-
Choose direction of Joint rotation 1
- Kelidor
September 14, 2023 at 1:31 PM
- Kelidor
September 16, 2023 at 2:29 PM
-
- Replies
- 1
- Views
- 501
1
-
-
-
-
staubli cs8c error: robot-ptcwarning: Motor_1_3_5
- Galet
August 28, 2023 at 10:36 AM
- Galet
August 28, 2023 at 10:36 AM
-
- Replies
- 0
- Views
- 695
-
-
-
-
Analyzing someone else's Staubli code 3
- RickyBrk
August 21, 2023 at 5:02 PM
- RickyBrk
August 28, 2023 at 8:30 PM
-
- Replies
- 3
- Views
- 891
3
-
-
-
-
RX130+CS7 Not powering up fully 12
- jmouw28
August 11, 2023 at 11:04 PM
- jmouw28
October 14, 2023 at 8:44 PM
-
- Replies
- 12
- Views
- 1.9k
12
-
-
-
-
CS9 password 1
- zyfhyfzzh
August 7, 2023 at 5:46 AM
- zyfhyfzzh
August 7, 2023 at 12:49 PM
-
- Replies
- 1
- Views
- 636
1
-
-
-
-
Robot Synchronization 9
- painful_staubli
August 3, 2023 at 10:43 PM
- painful_staubli
September 9, 2023 at 7:14 PM
-
- Replies
- 9
- Views
- 1.7k
9
-
-
-
-
CS8 Controller NOT Booting, MCP is Stuck Blinking at the Staubli boot logo 1
- painful_staubli
July 26, 2023 at 3:37 PM
- painful_staubli
July 28, 2023 at 10:49 PM
-
- Replies
- 1
- Views
- 945
1
-
Staeubli and Bosch Robot Support Forum
Please start a new thread only after using the search function to see if there is already an existing thread which addresses your question.
If you find a related thread, post your question there instead of starting a new thread.
Doing so helps to keep the clutter down and makes the forums more navigable.
Please give additional information regarding controller, robot arm and software versions with your question.
This is not an official Staubli or Bosch Robotics support forum. Please do not post copyrighted manuals or licensed software downloads.