Hello
When transmitting the program shows me an error " cmd timeout " . What can cause this error? Krc2 win95
Hello
When transmitting the program shows me an error " cmd timeout " . What can cause this error? Krc2 win95
what do you think it means? "timeout" is indication that something took too long... longer than reasonable. usually this means connection problem.
yes, I understand why that is after 2 min sending program appears this error.I'm just trying to send a program larger than usual. Do I have somewhere I can increase this time?
how exactly you are "sending" program?
From the computer, am sending by network to the disk d: . and then from the disk d: copies the c: to r1 / programs by kuka control panel. the problem arises when transferring from d: to c:
sorry but i don't think i can help you. you should consider providing some info,for example:
transferring how? using HMI or Windows?
what are you transferring? what is the file type and size?
by means of HMI . .dat files - 1 kb and file .src - 2 mb .
Never had that problem. How much did you mess with the registry? Can you transfer just one file? What is the total size of the files being transferred (the entire program). More info. It's most likely something that you changed or are doing wrong though. There's no clock ticking on how long it takes to transfer. On large programs of mine it can take 20 minutes to compile on the c: when moving from d:
the registry changed only
hkey_local_machine --> software --> kuka roboter gmbh --> cross 3 --> manager --> boot --> vxwinram --> physical pages 0x000061a8 (25000)
in the file hw_inf.ini changed A_PAGES=64 on 1000 and MIN_PHY_PAGES=10 on 100
QuoteDisplay More[Version]
office=FALSE;clock in microseconds
[Clocks]
commutation clock=125
position control clock=2000
system clock=2000
;clock in seconds
poweroff delay=15
;clock in milliseconds
emstop timeout=2200
;clock in microseconds
infh delay=200000
infh powerfail delay=1000000
[MEMORY]
;reserved Pages for one SRC-file (Min 16 pages)
A_PAGES=64
;reserved Pages for one DAT-file (Min 16 pages)
O_PAGES=64
; to guarantee a minimum of memory reserve for the system during
; SRC- or DAT-file loading, use 10 MIN_PHY_PAGES.
; MIN_PHY_PAGES is declared in per mil of all physical pages.
; set MIN_PHY_PAGES=0 to restore the old system behaviour.
MIN_PHY_PAGES=10 ; (allowed is 0 to 100)
[DSE-CAN]
;DSE-Programs
dsefile1=AUTOMATIC
dsefile2=AUTOMATIC
dsefile3=AUTOMATIC
dsefile4=AUTOMATIC
After these changes, I can send somewhere conc 1.5 mb file,as he wants to send 2 mb file gets an error cmd timeout.an error always pops up after a certain time of sending 2:05 minutes
and here the picture before the change physical pages to 25000
You can't just split up the 2mb file into smaller sub programs (like < 1.5mb)?
Hello
in PowerMILL never seen of such function to share programs, but by deduction and checked 3 available podprocesorów one divided into into 3 mb files .So I recreated it in a little notebook I looked for and found the lines with the amount of spitting by the subprocessor line changed at around 1.5 mb and it is oki
Thanks
In Powermill if you open up the PRI post (through the robot configuration tab in the simulator--post processor tab towards the bottom) you can set program splitting and the amount of lines you want per subprogram. It's a text file so you have to read down through it line by line...there is no gui set up to easily set parameters for the post.
Sounds like you found your own way though.
I'll check tomorrow
Thanks