hello mi robot rv6 problem error.
L1860 tlc ilegal parameter xyz.
(Change parameter??????
hello mi robot rv6 problem error.
L1860 tlc ilegal parameter xyz.
(Change parameter??????
Converted 2 sef to krc1 perfect
conversion sef to krc1 include
Rdw new.
Pc krc1 complete.
Wirings conection resolver....
The Spanish forum is dead. This is more interesting in English. I am Spanish and I always read forums in English. Spaniards never put information on anything they don't care about anything other than work. I think the rest of the world forums in English. It has more problems and solutions. Thank you.
After many hours of work and design. I managed to design a single board that would connect it to the krc1 mfc card ... valid for gm boxes. Wolkswaguen boxes. Kuka boxes. You can start the automatic start from the extension ..... we also have 4 optional outputs of 2 amps of power. 4 outputs over 100ma optional. and 6 24v inputs (without the need for a device network or any other communication. for robots with few outputs and inputs and simple start. (2 connections for external start and stop buttons. Everything is organized in this way. Configure mfc by removing commas (;) in mfc, then configure the external start entries in this order ext start 3 move enab 5 conf month 7 drive off 9 drive on 11. Normal entries have this order: 6,8,10,12, 14, 16 2 amplifier outputs 17,18,19,20 outputs 100mA: 1,3,5,7 and that's all folks.
Después de muchas horas de trabajo y diseño. Logré diseñar una placa única que la conectara a la tarjeta krc1 mfc ... válida para gm boxes. Cajas Wolkswaguen. Cajas Kuka. Puede iniciar el inicio automático desde la extensión ..... también tenemos 4 salidas opcionales de 2 amperios de potencia. 4 salidas más de 100ma opcional. y 6 entradas de 24v (sin la necesidad de una red de dispositivo o cualquier otra comunicación. para robots con pocas salidas y entradas y arranque simple. (2 conexiones para botones externos de arranque y parada. Todo está organizado de esta manera. Configure mfc por eliminando comas (;) en mfc, luego configure las entradas de inicio externas en este orden ext start 3 move enab 5 conf month 7 drive off 9 drive on 11. Las entradas normales tienen este orden: 6,8,10,12,14, 16 2 salidas de amplificador 17,18,19,20 salidas 100mA: 1,3,5,7 y eso es todo amigos.
Primero, con el teclado conectado de 5 pines. presione la tecla del logotipo de Windows ... (se abre el Explorador de Windows). en la siguiente carpeta: (carpeta kuka data krc (modelo de búsqueda abierto mada marca los 4 archivos con las teclas copia los 4 archivos con (ctrl + c). Salimos y buscamos la carpeta krka del disco kuka buscamos la mada . pulse el interior (Ctrl + v) pegado, se nos pregunta si aceptamos el cambio, apretamos (pestaña) en la pantalla principal buscamos arranque en frío y apague el robot, de nuevo al iniciar se cambia el modelo de robot.
alguien me puede ayudar a cambiar la mada en el armario vkr? Me estoy volviendo loco. Tengo teclado de edad también.
I think I'm going to tear out the entire control sef ... and throw it in the scrap. I'll ride krc1 ... with your rdw ... I don't get the manual or anything on the internet about sef. (I think this sef control is crap and nobody publishes anything about it)
Hello again. Modify software limits. And he didn't give an error anymore. Now I don't know how to move the loose axes ... and I tried everything and I can't move it.
hello thank you very much I have 4 robots kuka 2 are krc2 another krc1 and this sef ... your great help is greatly appreciated. there is nothing on the internet about sef. I have another robot that I will convert from sef to kuka krc1.
Help error joystick 203 limit down axis 3.
Controller vrs-1b
Hello manual vrs1 sef (for robot kuka vr125),
Hi, I tried it but I ended up totally crazy.
says that the interruption is not possible, something I am doing wrong ... I would like you to send me a simple program 1 point to another linear low point with the reading sensor interruption in input 1 ... with brake
si es un krc1 con unidad de servos de 6 ejes (monobloque pm6-600) cambiar cada salida a la otra salida, esa unidad lleva 2 salidas por eje. una de baja potencia y otra de alta potencia. si estan todos conectados a la equibocada marca trip en todos los ejes.
hello I have a controller for krc1 model box gm.
It has no auto mode, only ext mode. I would like to know what outputs I must use with plc to start externally (I want to program an external microprocessor that activates the robot) that someone explains to me in what order and time I have to send the inputs.
pgno type
reflect prog nr
pgno-leng
pgno-fbit
pgno-parity
pgno-valid
&ext-start
&move enable
conf mess