hello dears
i have a m2000 IRB4400
my controller can not boot up
in teach pendant a counter is counting and nothing will be happen.
in cpu status LED blinking (green)
where is my problem?
hello dears
i have a m2000 IRB4400
my controller can not boot up
in teach pendant a counter is counting and nothing will be happen.
in cpu status LED blinking (green)
where is my problem?
hello dear i have some problem with m2000 controller
1.how can i connect to m2000 controller with lan?
my controller has a lan socket
i need the software name and link
dose anybody have M2000 controller manual?
help me,Please
Type X (A/B/C) generally signifies a mechanical change on the Robot itself, not the controller.They could have changed gearbox/motor or (uncommon) a casting... If you look at the back of the arm it should say what type it is, if it's blank (eg. IRB 4400 / 60) then it's a Type A.
Again, look at the arm/robot, not the controller.
Thank you so much
hello dear i have IRB4400 M2000 controller
i want to make a system diskette with roboinstall
roboinstall asks me:
choose 4400 M2000 type A or
IRB4400 M2000 type B
in my controller plate is written
type: IRB4400 M2000
robotversion: IRB4400/60
how can i find that my robot is M2000 type A or
M2000 Type B?
Sorry for my late feadback
I changed FDD port number and its ok now.
special thanks from kwakisaki.
Hello Dears
I have a IRb2400 M97A s4 controller.
I lost my key disk and my robots serial is vanished
And ABB can not help me.
Robot Computer:DSQC363
Memory Expansion:DSQC317
Main computer:DSQC325
I have some RW3.1 diskette but i dont have any key disk
For RW3.0
But i can not instal RW3.1 on DSQC325
I want to know if i buy DSQC361 and insert it instead of DSQC325
Can i install RW3.1.
If somebody has diskettes of RW3.0
Share it with me, please.
Note: when i turn on robot
In touch pendant it write S4 not S4C
Thanks for every body
I solved this problem
I checked all of wire in controller side and robot side
And i could draw a diagram.
Now it is ok.
also you can check pins of socket.
one time i had this problem and it was for socket.
thanks for ever body.
but i can not use from this system pack.
Cause my controller is S4 and My cpu is DSC363
and i have to install RW3.0 or RW3.1 not RW3.2
if I use from that i will lose my boot flash chipset
thanks for our kindly attention.
re: that PM you sent.
My oldest 2400 is an M98 - the boot disk (if I can find it) probably won't work in your M97 machine.
There is a subforum for Manuals, Software and Tools for ABB Robots - you might check there to see if anyone has a M97 boot disk.
thank you so much but there is not in that subfroum.
thanks for your help
And special thanks from MR.Lanisoft.
I solve this problem.
I take out flash chipsets in DSQC363 and Re_load those and
Re_solder it.
Its ok now.....
I need disket of Program number 3HAC1462-1
can any body gave me it?
I have this message:
please insert disk (1) in disk set
with label: programNO3HAC1462-1
and press any key to start loading.
Hello Dears
i have a IRB 2400 with M97A S4 controller.
its S4 not S4C.
I lost my key disk.
can anybody help me?
Thank you so much
I learned a lot of things from you.
And you helped me very kindly.
I will do and I will give you feed back.
Best Regards,
dear kwakisaki
I found something in as program
I have c70 controller that I can connect with KRterm to it.
In SYSDATA I have:
FDD_SPD_BAU 96 96
FDD_SPD_STOP 2 2
FDD_PORT 1
FDD_SWITCH -1
But in c40 controller that one I can not connected to it .
I have this:
FDD_SPD_BAU 384 384
FDD_SPD_STOP 2 2
FDD_PORT 2
FDD_SWITCH -1
There are two different port number.
What do you think about that?
In c70 port2 is free but in c40 port 2 is used.
I'm afraid to change it to 1
Cause I only can connect with this controller with flappy drive
And if I change port to 1 and after that I can not to connet FDD drive
to it......
I don't have anyway to connect to it.
yes
i connected to bottom one.
Dear kwakisaki
thanks for your kindly attention.
I checked AUX95 before and both of them are CONN.
I tested it with 4 version of KCwin and KRterm.
I checked every things 100 times.
with this cable I can connect to another controller
and also I can connect to a Floppy drive.
I checked dip switches before and it was ok.
after powering up system is normal and it is usable.
after carriage return its flashing but I CAN NOT WRITE ANYTHINGS.
its so strange.
I only have problem with this controller.
hello dears
can anybody help me.
I have this problem yet
when I was trying to install win95
it progress some minutes and then I have stack over flow.
if I have a hardware problem, why I can start to setup.
dose anybody had this type of error.