Different software? I have robougide weldpro 9, but my real robot controler is frvrc 7.7
Posts by m3pisnik
-
-
Guys I have rail, from cad and have succsesfully integrated robot and rail motor.
But I can only jog rail when I set Group 2 Joint 1, but I need G1 J7 (G1 s) while I use this setting on real robot.
what to do?
-
Hy,
I have successfully set-up my working cell with my own cad.
But in start when I was configurating cell, I have set wrong limits, can I change it now?
I also cannot load backup of my robot, while mistake FRVRC 7.70, i have tried to instal 7.70 but it says it cannot be instal on win10?
-
I have tried this today, beacuse I was on hospital break.
After controled strat and pressing FCNT I cannot acces to Backup, scren just blink and is on previus screen.
Don't google, use search funtion in this forum:
-
Ok, I figure it out.
Have to put $prg_cmd 2 instead of 0.
Thanks
-
I hace choose it, but cant do anything?
See pic
-
Sorry, I selected wrong picture.
Here is actual.
-
So here is my program.
Offset is just Z- 500mm.
-
Hi.
I have move to another location my plazma drop place.
And when i go to Pr, and record new position, the actual position is new, just until I change tool or reset robot.
How can I permanently change PR of my tool?
Thanks guys
-
Take a previous backup of your robot that has the correct weld procedure information. Power up the robot into Controlled Mode and then load the AWSETUP.SV file that is in the previous backup of your robot.
I have googled controled mode, but I dint find anything usefull.
Can you tell me, how to get in controlled mode?
Sorry newbie on Fanuc
-
Loading AWSETUP.SV in controlled start should fix this.
Can you tell me more?
-
I have pressed button clear instead of select in weld proces.
So now I dont have Job Mode in weld process and I have to manualy sellect program on frounius.
How can I get back Job mode?
I have back up, but i dont know how.
-
Hey.
I am currently welding some plates of thickness 3mm, and there come 15 plains on thickness 10mm.
So I have problem. We get plates and this straight(plains or ehat are they called in english) from buyer.
We need to weld them to plate and then post-production.
We became plates which are 2000mm*1800mm but this straight, are constant in lenght and height, but they vary from 18-19.5mm in widht.
So i have problem welding the.
One plate take about 1hour and half of welding, and one hour off preparation and so on. we have at least 150 plate to make.
So I want to use tast.
I have current arroung 170-180A, vellocity off welding is 42cm/min.
What I have to done in Tast to make sure my robot will weld straight?
I dont know any of this oarameters in Track.
Can anybody send me some approximatelly work?
-
"T.A.S.T" application varies according to the work situation and project. You have to produce your own solution about the subject yourself. After all, nobody is as close to your source material as you are. I can send you the "FANUC_R-J3iB_ArcTool OPERATOR'S MANUAL (B-81464EN-3/01)" document which describes "T.A.S.T" application in this regard. Please send me your email address if you would like to review it.
Can you send me?
-
-
Hi. I am gettin alarm int253, 251, when i want to start program.
I have selected tool1, and points are made with tool1.
What is problem?
See picture.
-
Guys, I had pushed button clear instead off select, so in my weld proces, now I dont have option Setup (no weld) and I cant manually do nothinf on fronius controler. What can I do?
See picture
-
What?? Which 'right' and 'left' do you mean? Please clarify the two contradictory statments. On the picture there is nothing clarifying to see.
On the left I can run program, but for editing i mist go to the right window.
See picture, on left window, there is no option for point, arcstart and so on.
-
Yes, I know.
But I can edit it only on right window.
See picture.
Thanks
-
I can edit program only on left window and play it on right only.
How can i change it? Its really anoying