Well now it is stuck at infinity startup loop.Will go for hyperterminal procedure
Posts by Mertkan Koca
-
-
Look in the manuals and software subforum for the document which describes how to use hyperterminal to commect to the cpu via serial link and delete the image.bin.
I will bring another laptop which has COM port and try but i just wondering..
Robot starting up normally booting is good and system working RW1.40 right now. Problem is inside the FileManager i cant delete previous system files . Can i delete them with FTP Filezilla and do C-Start and try to download system again ?
-
CPU-DSQC500 And old system was RW 2.23 now i am using RW1.40 cant even see shutdown button i connected with FTP to show hd0a.As you can see
Robınstalls downloaded corrupted systems which i created to install RW2.23 systems.but boot image didnt installed them now I cant delete those 99-00013 , sys1,sys2 system folders from TP. What should i do to make clean boot and install 2.23
I am asking because it cant redownload system to controller
-
CPU-DSQC500 And old system was RW 2.23 now i am using RW1.40 cant even see shutdown button i connected with FTP to show hd0a.As you can see
Robınstalls downloaded corrupted systems which i created to install RW2.23 systems.but boot image didnt installed them now I cant delete those 99-00013 , sys1,sys2 system folders from TP. What should i do to make clean boot and install 2.23
-
-
Looking at the CPU card:
The DSQC500 has T1-3/4 (5mm) LEDs
The DSQC540 has T1 (3mm) LEDs
Doesn't hurt to double-check.
I wouldn't worry about the corrupt system yet unless you run out of memory.
You should be able to load a good system and select that.
On the teach pendant, does it show the start screen with the 'Select System' screen?
If it does, you might be able to select the corrupt system and delete it from there.
Hello lookings like i have DSQC500 but i dont understand how it is possible old version on backup old system was 2.23 ? Which version should i prefer
-
What was your CPU ? Robotmei DSQC500 or DSQC540
-
I created yes but it is in RobInstall i wasnt able to use backup files now i can use them . no more failed to create file key.id error. i can finish the editting.
I will try to update boot image tomorrow morning.
Skooter i checked cpu but need to remove metal panel first i will check again.Previous RW version was 2.23 i think it should be ok.
Right now my problem is I installed RW1.40 but i cant delete uncomplated downloaded systems from hd0a.I need to erase them they are already downloaded to controller but they are cant installable corrupted files so i need to clear everything
I will back tomorrow thanks lot
Best regards
-
Lemster68 and i downloaded RW1.40 to controller but in hd0a there is other system files which i cant delete and in format section i cant format hd0a
-
At first i did X start to see if there any other sytems in controller and then in the x start page
i direct connect ethernet then try to download created system and this showed to me after that i did C start and download system but in X start page it showed me this message then i did C start and downloaded system i think boot image version was different one is 6.05 other is 6.22.At this message i select cancel i didnt continued.
I want to format Hd0a but it says cant format and i barely see other system files at file manager
-
Create the boot disks just so you have them. Going online with the controller to install is pretty easy.
Things getting interesting , I did C-Start and after that downloaded to system to controller it was succesfull and asked me to reboot controller yes or no then after reboot installation started and this error happened.What is the problem i am so confussed
-
Hello Lemster68 and Skooter Thanks . You are bein very helpfull more than ABB !
As you said before , problem is because of the installer. Each baseware has its own installer so mine CD is not match with backups so could you please anyone can upload RobotWare 4.0 3HAC6811-2.23 installation file I asked from Abb but no response. Skooter Lemster68 .
Best Regards
I solved the issue and created system then changed language exact RW 2.23 from backup key
I found 2.27 Installer and add 2.23 to media pool then used my backups with serial number
now looks good.Next step is installing which should i prefer Download selection or Create iboot disk ?
-
Hello Lemster68 and Skooter Thanks . You are bein very helpfull more than ABB !
Hello. It sounds like they are being very helpful. My next suggestion would have been to go back to the original installation beginning with the older baseware. From there, you would have been able to update the system with newer baseware. Regarding the main computer, it may already be upgraded, since it does have > 2.02 already, 2.23. Just open the cabinet and have a look.
As you said before , problem is because of the installer. Each baseware has its own installer so mine CD is not match with backups so could you please anyone can upload RobotWare 4.0 3HAC6811-2.23 installation file I asked from Abb but no response. Skooter Lemster68 .
Best Regards
-
Hello again , I tried to open floppy disks only 3 of them (4-5-6 numbers) disks worked and the other 4 floppy disks 1-2-3 and FactoryWare disk are dead.
Any more solutions ?
i asked RobInstallers newer version from ABB to use key baseware setup and i asked FactoryWare disk from factory if backup key not work for baseware we need factoryware disk to use backup key.Otherwise i will use my RW1.40 key and no more 2.23 version
thats is ABBs message to me : If you request, I can send you the RobotWare 4.0 3HAC6811-2.23 installation file. With the FactoryWARE DESMA 99-00013 option you have, you can perform the system setup in English. But in order to do this, you may need to change the DSQC500->DSQC540 main computer board. 2.02 and later will need this card. Sometimes the installation can be performed. It can be tried.
-
Hello i have been using the usb floppy emulator successfully thats how i got backups from controller . also tried to connect service port test good i can connect to controller with laptop no problem. The big problem floppy disks are dead i think.I Just got usb floppy drive and tried to read inside floppies but it is not working.I really need a new RobInstaller to open mine RW2.23 backups and same signature type to change language
-
Just so you know, there is no need to delete the older versions in the mediapool. It is a good thing to have as many versions as possible.
Thanks lot , is there a any way to export RW and other additional keys from Controllers hdd ? I did normal backup but until flooppy reader arrive to me i want to comminucate controller with laptop and download datas with using RobInstall.After accsess floppies i will be back sir thanks
-
Each version of the Baseware has its own installer. Did you install those using the installer?
Yes i downloaded the drive and change the folder at mediapool and select preferences and erease 1.40 and it shows 2.23 but like you said we should check blue floppies
-
Ok sir thanks once i get floppy to usb converter i will be able to open floppyies and will keep here updated !
Best Regards
-
It could be a compatibility issue with Win 10. Here is the next thing to try. I saw in one of your photos that you had the system selected in the robot browser. on the right, you will see the keystring used to create the system. You might have to scroll down. Highlight the keystring and copy it. If I recall correctly, the shortcut keys to copy do not work but you can right click the highlighted keystring and select copy from the dialog box. Paste it into a text document and verify it is the same. With this keystring, you can create a new system. Try that.
I tried no problem with Win 10.I have both keys from backups i can copy key i can see no problem but it is not accepting 2.23s key and says error failed to create file key.id. If i try old RW with old key no problem .mine robInstall v1.30 is not accepts RW 2.23 keys or cant make correct them it only accepts its own key RW 1.40 do you have any solutions or any robInstall newer versions which can accepts mine backups 2.23s signature 10 keys
Other thing how is the installation RW 2.23 file destination which you just upload.I am selecting file to import Mediatool and deleting old 1.40 RW thats how i do.Do you have RobInstall type unpackeged files RW2.3
backup key is signature 10
robinstall key is signature 8
thanks best regards
-
Delete all the folders for the robot that have been created. Go back to the first step in which you make a new folder with the the robot serial number. Copy the two files same as before from the backup. Now you have the expected baseware in your mediapool. You ought to be able to select that robot in the robot browser and make the desired changes. Forget about the robibstall cd key. It is for an older baseware revision. This is the reason that we are starting with the backup files.
You are welcome.
I tried but still same error : failed to create file key.id
i think it is because of RobInstall version do you have new version mine is v1.30 or it is because of Win10 should i use Virtual PC ? I will record video and upload to show you sir.We progressed very well but this error :(( also i changed serial no robot and backinfo serial no is differend i am liitle bit confussed