Hello,
I only have RobotStudio + RobotWare 5.07.04, received from Massula few months ago.
There is an option to upgrade from 5.07 to 5.14 going step by step. I remember that this procedure is described on the ABB official forum.
Hello,
I only have RobotStudio + RobotWare 5.07.04, received from Massula few months ago.
There is an option to upgrade from 5.07 to 5.14 going step by step. I remember that this procedure is described on the ABB official forum.
yes. The green is the TP.
But as i say, i am not worried about not.
I could inspect the flash but unfortunatelly i delete the MC.bat file from the OS system. Now the controller does not boot anymore and the led is red. I am still searching for commands that can bring me to factory reset.
Because the PC was removed from the system, this controller must be reset to the factory settings again. And this seems to be possible only through the serial port with OS commands.
Do you know any of them doing this?
the blue connector is the VGA
the pendant belongs not to this system.
i bought it later and in this moment on booting it displays IP class 126 instead of 125 as in the controller.
i must change the Flex Pendant IP later.
i did not give importance to the flex pendant for the moment.
i am focusing on the controller communication issues because the controller does not comunicate proper with the RObot Studio and it should regardless to the flex pendant.
if i press TEST for the communication than i get OK message. when i want to transfer data, than i get that message with connection error give by the not finished booting. this is what i read. Not possible to link as long the booting is not ready. he is feeling the controller as he did not finished the boot phase.
yes status.
Do you know where i can find the reset command to factory default on serial communication?
I manage to establish a link communications through RS 232 but i am not familiar with the language.
There must be a setings made before when the PC was connected. Noi i must do the factory default. The serial was the best way to get into a dialog with the controller.
no. I do not have.
This controller was working with a PC on top.
I receive it without that PC.
It seems that on booting phase the controller is waiting for a confirmation or a information.
Could be this because of the missing PC?
Anyway the PC does not boot till the end.
And I cannot evaluate the flash memory if it has a problem or not.
regardless if I put or not the USB Stick into the CPU.
Power green led ON.
Yellow led blinking few second than go OFF.
Service interface led green ON.
from the oficial ABB I got the information that I need a memory disk with the image on it to be able to reinstall the software. Not possbile from the RS5.
article number is:3HAC020988-008 and 245 euro.
Do you see any other option for me in this moment?
I tried to install from USB because I do not see any other option for the moment...
No Ethernet connection, no floppy or CD Drive.
the teach pendant stays in the same icon with the moving bar searching for the controller.
I tried all the options.
When I put it in the controller I hear a bit tone. But this is all.
The. Monitor is in the video output of the controller.
I tried to boot with the USB Stick but does not work. The controllers not see the USB. Stick as a boot device. I was changing in Bios the booting to USB but still nothing.
The controllers is asking for an operation system.
Also not possible to send the files through the Ethernet as long the controller is stacked in the booting phase.
I will attach some pictures with the files I get on the USB stick.
Can you help me with other steps I have to follow to make the controller install an operation system?
it works!
With Windows 10.
I could generate based on my Keys the Boot Media file on a USB Stick for that old version.
Tomorrow I will go to the robot and check if it finaly works on the controller.
Do I need to do anything special? Or only put the USB stick into the Service port and wait to boot the program?
very much apreciate!
I will check and let you know with a feedback on Monday.
thanks a lot!
I have changed my username in the mean time. just to inform you....
RS 6.03 and i need RobotWare 5.06.01.03
Up to V7
There is no V5 and cannot be downloaded
that list stops at V6.0