I see that you use kr200l170 to cut granite.
I have got a kr180 & kr150 for cutting marble 2-3cm.
Is that payload enough for cutting marble?
How many kw is your cutting motor what rpm and what is cutting disk diameter?
Posts by javaman
-
-
sure
i have some sdram pc133 modules i think 256mb or 512mb per module.
The procedure is to install winxp embedded and after that kss v5 ?
Can kss v5 work with old krc2 mfc2 & dse-ibs or must replace these cards with newer ? -
Can i install v5 kss in win xp without changing mfc & dse-ibs ?
-
soyo sy-7vba133k get 3x512mb pc133 sdram registered-eec or unregistrered-non ecc ?
kuka software(kss) that runs in win95 can run in win xp embedded without changing mfc&dse-ibs ?
I mean to run kss 3.x.x or 4.x.x on winxp embedded. -
Except changing mfc dse-ibs ram & hdd needs some rewiring as reported in previous post?
Do you know an estimation of cost for mfc3 & dse-ibs c33 ? -
KRC2 have Soyo motherboard
Ed05 have Fujitsu Siemens motherboard.KRC2 running with MFC2 ISA board and DSE-IBS 3.2 or C33
Ed05 running with MFC3 PCI Board and DSE-IBS C33KRC2 running with Celeron 733 Mhz Cpu. (Shipping version may different)
Ed05 running with Celeron 1 Ghz Cpu. (Shipping version may different)KRC2 suitable for KSS 3,4,5 versions. (KSS 5.X.X compatible with DSE-IBS C33)
Ed05 only KSS 5.X.XNice information.
So theoriticaly changing the MFC2 to MFC3 / DSE-IBS 3.2 to c33
adding at least 1gb ram to soyo mobo and changing hdd with one ed05 software
you can convert a vkrc2 to krc2 ed05 ?
Have anyone done a modification like this? Is needed something more ? -
Manual has only the electric diagram.
Can you give me a link to operational manual of vkrc2 ?
Yes the latch but how can release it now without key? -
I have received a used vkrc2 robot and i have opened the door of vkrc2.
After i closed and i cannot open again.
It has keylock but i have no keys for the vkrc2 door.
How it is locked on it's own ?kcp2 does not have the spwcial 6 axis joystick how can i jog without this joystick?
Also how i can change kuka software menus to english from german that is now?
Thanks. -
There are serial rs232 adapters (DB9) to rs485 modbus (A/B).
I can put this adapter to a free rs232 port of vkrc2 pc.
The problem is the software how to drive the pc rs232 port from kuka software. -
I have a 3.5kw 24k rpm spindle & inverter that takes analog +-10v or 0-10v & dir input.
Also inverter has serial modbus input is allen bradley powerflex 40.
How can interface it with vkrc2/krc2 (win95) for soft milling operations? -
I have vkrc2 control with win95
What i need to convert it
1) to krc2 with win95
2) to krc2 ed05 winxp
?
Is krc2 better than vkrc2 ? -
Sculptures need a lot of material removal.
This only can be done efficiently by diamond cutting disk not router bits.
Robot does not have the rigidity for attaching motor with cutting disk.
So cnc is more good option for sculpture. -
What doing X11 & XS2/XS3 connectors (vkrc2)?
What are the differences between VKRC2 & KRC2?
A kcp2 pendant for krc2 control will work in vkrc2 control ?
A ksd1-32 can replace a ksd1-16 (for the same motor)?
Can i convert a vkrc2 to krc2 ? -
If we compare robots of the same class for example 150kg & 200kg payload
which robots from the big manufactures fanuc kuka abb yaskawa are the best mechanically?
In terms of accuracy repeatability durability easy to repair.
Only mechanically not electronics/software/electrics ...
Also if you are in europe which brand you can get more easy mechanical part spares ? -
I have tried old agp but does not show anything.
Iam sure that pc works because i see correct activity to hdd led.
I have tried
1) only kvga -> no output to vga
2) only agp gpu -> no output to vga
3) only generic pci gpu -> no output to vga
4) both kvga & agp gpu -> no output to vgaSo i will wait the other robot that has pendant and i will use the other pendant to verify correct operation.
Also i will try to clone the kcp2 pendant esc circuit. -
I found in my old pcs scrap a nvidia agp 8x gpu and a pci gpu
very old hardware but in working state last time used.
Can i remove the kvga put my agp 8x gpu so to have display make the registry fix
and after do the registry fix remove the agp gpu and put again the kvga ?
Is there a risk kvga driver deleted accidentally ?These gpus will work? (i found them inside some very old pcs)
agp (Trio3D/2X) http://vintage3d.org/trio3d.php#sthash.8BHu7KpZ.dpbs
pci (Virge/DX) http://vintage3d.org/virgedx.php#sthash.sJj1QcKQ.dpbs -
Where is the post that explains what must edit in registry to enable external monitor?
(I will clone hdd before any change) -
I got the robot.
Also i got an another robot that has teach pendant but this is not in my hands now
i have only the robot with the missing teach pendant.How can i enable the external monitor without the teach pendant?
Also connector X19 has in the centre 4 pins ABCD that are for kcp display monitor.
What are these 4 pins? Can i connect a vga external monitor temporary to these pins
to make change in settings so external monitor enabled?Iam interrested what pins 1/2/3/4 in X805 connector do
DISPLAY+ DISPLAY- RES RES -
Sorry for the lazy questions but i have not have the robot in my hands now(is on transport)..
Used KCP2 has cost about 2k euros so i got an other same full robot (kcp2 included) for 3.5k eur.
So i will have one robot with krc2 controller and the other robot with a non kuka modern controller. -
I have not the manual...
inside R1\MADA exist joint lengths ?