Finally i've used a maple systems HMI.
Posts by jleblanc
-
-
-
-
Hi,
I want to know if someone is familiar with softfloat option. I use it to take a part in a diecast machine. All work great. The question i have is about the time it took to go in softfloat. It's between 1 and 2 seconds and i want to decrease my cycle time. I want to know if it's normal or if i can do something to decrease that time.
Thanks.
-
Hi everybody,
I'm trying to use the force condition in the Prog Select for the single step. I've made it for the general override<100% and it's working great. But i'm not able to make it work for the single step.
R30iB controller
Check: Single step
1 Check when run: ENABLED
2 Check when resume: ENABLED
3 Prompt if failure: DISABLED
Post error if failure: ENABLED
4 Post warning if forced: DISABLED
5 Force condition: ENABLEDThanks.
-
Hi,
i agree for the lightning. We have a bunch of vision system for other aluminium product and light is the key for success.
i think i will give a try to iRVision 2D.
Thanks for reply.
-
Hi,
i would like to know the orientation 1-360 of an aluminium pulley about 4" diameter to feed a rotating table at x angle.
About 2.5s cycle time.
Thanks.
-
Hi everybody,
i want to know your feelings about iRVision 2D. Is it easy to use? Or did you use another brand vision system like Cognex, Keyence, ...
I have a project with a LR Mate 200iD/4S (Short Arm) and R-30iB and want to know if i will use Fanuc Vision stuff or anything else.Thanks.
-
Hi,
all the coupler config fits the robot config 3 Words In and 3 Words Out and instance are ok 101 for input, 100 for output. I'm just not sure about the unicast-multicast and the O=>T T=>O. But the communication is RUNNING. I suppose these parameters are ok. The problem persist. I have ouput 1-4 after that i have 21-36 anf finish with 5-20.If i make these config the output are in the right order.
Range Rack Slot Start
1-4 89 1 1
5-20 89 1 21
21-36 89 1 5But i want to understand why it's not working like the input.
Range Rack Slot Start
1-40 89 1 1Thanks
-
Good afternoon folks,
i have configured ethernet IP for a Phoenix IL EIP BK DI8 DO4 with 32 in and 32 out + the 8 in and 4 out on the coupler.
It's working great for input and output 1 to 4. But the output 5 to 20 are invert with 21 to 36.I would like to know why.
Controller R30iB
DIO Config :
Input
Range 1-40
Rack 89
Slot 1
Start 1Ouput
Range 1-36
Rack 89
Slot 1
Start 1Thanks
Jonathan -
For testing the collision guard i was in jog reduce speed and i 've hit the jonction of the J5 and the arm J4 and after a few moment the controller has gone in an Overload error. I don't remember the code.
-
Good morning,
I have only enter the weigh of the gripper with and without the part. I've not entered the rest of the settings because i did'nt have it.
I have the Payload check option but don't know if it will work with my gripper.
Is it supposed to give an error anywhere the arm is hit or only if the gripper is hit?
Be comprehensive it's my first project with a Robot.
Thanks.
-
Hi,
I have the collision guard option installed on my robot controller R30iB.
I want to know if it's supposed to work in T2 mode?
In the collision set-up it's enabled and at 100% but does'nt seem to work.
Thanks.
Jonathan
-
Hi,
i'm able to copy back the aoa files in the FR: of the real robot but after that what i'm suppose to do?
Thanks.
-
Hi guys,
I have create a robot in Roboguide with the All Of above of a real Robot. Now after deleting some programs and made a few changes in I/O comments, Payload, etc... I would like to know how to create an All Of Above Backup in Roboguide to put it back in the real Robot.
Controller R30Ib
Transfert method is FTP.Thanks.
-
jleblanc - Are you able with the Maple Systems to access Register and String ??Hi,
I have use I and Q but there is other Memory Type like M, G, T, SA, SB, SC, S, R, AI, AQ, W.
-
Hi guys,
I have the same issue and want to know what was the problem.
Thanks.
-
Hi,
finally i've done it with a Maple Systems (HMI5070NLv2) approx.640$CND and it's working great.
Thanks.
-
Thanks guys,
I will try Proface instead of Quick Panel+.
Which series of Proface is the most suitable?
Jonathan
-
Thanks DaveP,
if i'm not able to make my HMI working then next step i will buy a GE Quickpanel+ HMI it's seem to be working great.
Thanks again.