Hi everybody!
My RJ2 is paused automatic when execute the wait instruction long time. Help me please! thanks.
Posts by heroman
-
-
Dear everybody!
I have a tool to backup for Fanuc RJ2, this is Fanuc cassette adapter. Because, I afraid other day, battery for controller is empty. I want to creat backup file. But I dont known method to perform it. help me please. Thanks! -
You should replacement Servo Motor (encoder).
-
Dear everybody !
I have a problem: when I start ROBOT RJ2 from Start Button in Operator Panels is OK. And I dont known start from External start. Although I switch on Key to REMOTE. I connected follow picture, but ROBOT dont run. Help me please. Thanks -
I have a XRC CR50 old Robot. I want to change the speed, because the speed was limit by management mode. I dont known ID of management mode. ID default was change. I want to reset ID now. Help me please. Thanks
-
yeh, I did it OK. Thanks robotero, kluk-kluk, Iowan . I am very happy !
-
who can help me please ? thanks!
-
While on EDIT move the cursor right to the position number or position register number and press F5[position]
If position is uninitialized data appears as *****
To initialize you don't need to be in the PR screen,
Just move the cursor back at the beginning of the motion instruction and use touchup [F5] to record the position
Post picture of your EDIT screen at the error point
Dear !
I press EDIT appears as figure 1:
I move the cursor right to the position number appears as figure 2:
I press F5 appears as figure 3:
I choise choice 1 appears as figure 4: (1 XYZWPR axis, 2 J1J2J3J4J5J6 axis).
I move the cursor back at the beginning of the motion instruction and use press [F5] appears as figure 5:
I don't known to record the positon. Help me please. -
Copied from another post:if you want to change the language of rj2 robot
you have to follow below steps
press 1) menu
2)next
3)system
4) variable
go to language variable & press default
after that
you have to do
1) menu
2) setup
3) f1
4) general setup
you see 3 no. option for current language change
select that option & press ok you see two option
1) japanese
2) english
select 2 for english language
after that you see your language is change to english.ジッコウ [JIKKO] translates to EXECUTION
I am pretty sure is INTP-311 uninitialized dataCheck your program, probably a position register, or a position is un-initialized
My controller have "DEFAULT" only. No English.
Can you guide me method to initialized position please,? -
password protection or maybe quick menus enabled.
I try to found the "Password" when I go MENUS -> SETUP -> F1 -> but I dont see "Password". although I choose FULL MENU enable. -
Hi J-dornezif you want do initialise your PR you have to go to
DATA -> TYPE (F1)-> Position registerAnd after this you have to go to your register, for exemple the number 10, press POSITION (F4) et modify all the *** by a 0 in all axes and group you use
I go to DATA -> TYPE(F1)-> "Register" display only. "Position register" no display. Why? -
I go to MENU-> DATA-> F1(TYPE) . Display Register only. Position Reg and Pallet regis ect... no display.
-
I run the I/O statement is OK. But motion statement is fault -311. I am sure INTP-311 mean KAREL program error. Untaught or uninitialized data was used. But I dont know to solve this problem. help me please!
-
This is the errorcode
-
Even, i press SHIFT + FWD or SHIFT + BWD Robot alarm too. Robot dont action.
-
Dear everybody!
I have a Fanuc robot S12 RJ2 (interface is Japanese). I creat a new program, When I start the program (Local mode), robot have alarm INTP- 311. I can't solve this problem. help me please! thanks. -
Dear everybody!
I have a Fanuc robot M12i RJ2. I want to creat a new program. I press SELECT but sreen don't display CREAT. So I can't creat program, Help you please. Thanks.