Hi alls
I buy a Robot arm with Yasnac ERC K3S but i don't have any manuals about it.
I hopy someones help me please ....thanks alot
Posts by anthony
-
-
-
Hi .I has some things you looking like that.kawasaki JS 6with A controller. All the operation is normally.
If you still want buy it ,please PM to me.
thanks -
Hi All .i have a Kawasaki J manipulator .A controller .i don't have anydocument about it.
recently how can i do encoder reset?
thanks. -
Hi All
I had Js6 arc welding with a controller .now it's get a error 1500 & 1504
i'm not alarm list and basic operation manuals. please help me process remaster .
best - regard -
Hi,All
I have to learning about A08F-A controller with JS6 manipulator
Is there any one know this controller and work with that .
i need basic operation manuals about themMany thanks and best regard
-
thanks so much Desto
I have not R-J2 Teach pendant other,measure test a baterry so good (a new one)
i tryed depress the same your way but it nothing change on screen. -
thanks Desto
This type a Fanuc LR matechange 200i with R-J2 mate. i take out CPU board and cleann up but it not to change .
now what can i do -
Hi Desto
I has to try many time but it too.may be it can be reload system software? -
Hi All
Help me please
i turn on R-J2 controller and then i get it on display . i not yet to back up data system
now i can not to make anythings.
thanks
I attachments some pictures status on tp. -
hi .
how much do you like for sale it? -
Hi i just purcharged a osacom 6800 .when i turn on power controller ,after dianogstic system i saw on display 030 -040=040-071.what does it mean ?
but i can not turn on servo . a relay turn on servo puton status to work well .on displayed < Please put turn on servo button > . but i put it is do not change anything ?help please ..
-
Hi
MRC SK6 just reinitialize i miss back up with Welding Application. now it Will be not Erorr Feedback ( Not Current detecion) it has inclucded MWE 01 PCB Interface with Welder source,Turn on welder but not arc manipulator still moving on line.not stop .
now i like offset that signal Current Detection in Ci/o.or Ladder
Please help -
Hi. PCarb. This controller is Arc application
I needing Turn on / off welder signal ( arc on ) and feedback signal ( arc start - if it lost feedback signal it get alarm 9010 / 9020 No Arc ) during move arc .not need to correct Amp ,Volt. Because On welder source has cracter
This case is MRC K3 cotroller not MEW 01 pcb with Nastoa 350Y i/f ínide. when in sert arc on comand it get alarm 5520 because in slot not Mew01 pcb . Be sure In Mccb 02 it has this signal but i not yet to find which pin out. CNB1----CNB5 slot. May be CNB5 .
I needing to make soon .please help -
Hi Pcarb
I not need wire speed (Amp)and heat (Volt) only have turn on welder and arc start reponse so it during move incluced arc on comand in program if it have error from welder it will stop at . The basical if have not MEW 01/02 PCB is that signals to use for all application not arc only.
- handing application .while clamped a metal sheet to move if it crash down is manipulator will stop . in this case ( arc application) it the same.
I want to findout two signals on/off and reponse signal from system on MCCB 02 .not to use Dout or Din .
if you can help me please, -
Hi all
I just purcharged Motoman MRC K3 . it using Handing application .now I want to change it Arc application.
It not to used MEW 01 board or MEW 02 board.now i would like connect it to welder controller .
it using MIO 04 board only . If it can make I need two signals is. Arc on ( click arc On welder ) and Arc start reponse from welder to move instructions in program.
This case can I to make it ? and How can i do it ?
thanks - please advise . -
-
Hi all
A Long time i turn off power now i turn on it get alarm 120 . that why ? what't the happen ? i
looking for in manuals it not this error code.
alarm 120 encoder comunication error S and L axis. -
this alarm i looking for in manuals i can not to see it.
-
Thanks Robodoc. exactly i get 2100 .i take out moteur ,It 's was bearing damaged. i woud like to change bearing other .then i reconnect it again but i get alarm 120 .encoder communication error.R1 S.L axis.
now i can not move and turn on anythings.
why it happen ?but it's before everythings all display so good.