July 19, 2019, 12:37:23 PM
Robotforum | Industrial Robots Community

 Alarm codes 5011 and 5053

normal_post Author Topic:  Alarm codes 5011 and 5053  (Read 2049 times)

0 Members and 1 Guest are viewing this topic.

February 04, 2018, 02:10:21 PM
Read 2049 times
Offline

asgary64


Hello

We are connecting laser tracking sensor. we have problem with it and when we start robot we have alarm codes 5011 and 5053 same as bellow picture.
what is problem?


Today at 12:37:23 PM
Reply #1

Advertisement

Guest

February 05, 2018, 05:47:30 AM
Reply #1
Offline

rAviteja_g


5053- Laser Tracking processing error (An error occurred at the end point search processing)-  Adjust the vision sensor to do the steady detection.

February 05, 2018, 12:01:07 PM
Reply #2
Offline

tony gast


5011(0001_0101) Transmission error is  occurred between the controller and laser sensor unit.
Reset the alarm
Turn off the power of controller and Laser sensor unit, and turn on.
Check the connection between connector on control board and the cable from laser sensor unit.
Replace control board board and the cable.

5053(80) Data error is occurred in sensor process.
Turn the power OFF then back ON.
If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your Yaskawa representative
Oh, well

February 06, 2018, 09:04:59 AM
Reply #3
Offline

asgary64


Hi Thanks.
we connect laser and DX200. when we turn on laser from PP we have this error(picture)
Our sensor brand is Metavision.
Can you share all manuals and settings for this brand with DX200?

February 07, 2018, 11:41:00 AM
Reply #4
Offline

David Casella



5011:
Meaning - Transmission error
Cause - Transmission error is  occurred between DX200 and laser sensor unit.
Remedy - (1)Reset the alarm, and then try again.
(2)Turn off the power of DX200 and Laser sensor unit, and turn on.
(3)Check the connection between connector on JANCD-YCP01 CN104 and the cable from laser sensor unit.
(4)Replace JANCD-YCP21 board and the cable.

5053:
Meaning - Synchronized timer error between DX200 and laser sensor unit
Cause - Software operation error occurred
Remedy - (1)Turn the power OFF then back ON.
(2)If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your Yaskawa representative about occurrence status (operating procedure).
David Casella

February 08, 2018, 06:30:51 PM
Reply #5
Offline

asgary64


We solve problems. we are calibrate robot and sensor. in calibration job there are SKILLSND command. when we run calibration job it to be run and when it receive to SKILLSND command it stay in this line. what is matter?

February 15, 2018, 07:30:50 PM
Reply #6
Offline

David Casella


I don´t know what this, SKILLSND. I don´t remenber this. Sorry. I will find about this.

Cya

Today at 12:37:23 PM
Reply #7

Advertisement

Guest

February 15, 2018, 07:41:36 PM
Reply #7
Offline

David Casella


We solve problems. we are calibrate robot and sensor. in calibration job there are SKILLSND command. when we run calibration job it to be run and when it receive to SKILLSND command it stay in this line. what is matter?
I don´t know what this, SKILLSND. I don´t remenber this. Sorry. I will find about this.

Cya
[/quote]

Please, contact the representative for the manual about this.


1     MotoFit Function
1.1  Overview of MotoFit Function
1-1
DX200 MotoFit
1
MotoFit Function
1.1
Overview of MotoFit Function
The MotoFit function
1)
 achieves a precision fit
by a robot by detecting
external forces acted on the tool coordinate home position with the 6-axis
force sensor to correct for the manipulator position.  The 6-axis force
sensor, which can detect three tran
slational forces and three axial
moments, is installed at the manipulator's tip in order to detect external
forces in the job involving "Touch".
Normal control is a position contro
l which retains position even when
external forces are applied.  The MotoFit function, on the other hand,
achieves a precision fit, with a force
control, correcting position to match
the force acted on the tool coordina
te home position, based on the force
feedback.
The MotoFit function incorporates the following four special commands
suitable for the positioning of precisi
on parts for a clearance from approx.
10μm to 100μm.

• SKILLSND "TCH: • • • "  : TOUCH (TOUCH)
• SKILLSND "FIT:   • • • "  : Search (FIT)
• SKILLSND "INS:  • • • "  : Insertion (INSERT)
• SKILLSND "IOF"            : Finish Force Control (IMPOFF)
Besides, in order to adapt to the hardness of various kinds of workpiece,
such as plastic, wood, and metal, the force condition file, in which optimal
parameters can be set according to
the hardness of a workpiece, is
prepared.  Use the MotoFit Function Engineering Support Tool for the
settings in the force condition file.
(Refer to DX200 MotoFit Function
Engineering Support Tool.)
Besides the above command the four force sense basic commands. 

• IMPON (Macro Instruction)
• FREF (Macro Instruction)
• FDET (Macro Instruction)
• IMPOFF (Macro Instruction)
« Last Edit: February 15, 2018, 07:43:35 PM by David Casella »

February 15, 2018, 08:30:13 PM
Reply #8
Offline

asgary64


i have SKILLSND instruction in all of macro jobs. for example i see SKILLSND "LSRCHST LT:1 B0:2 B1:3 B2:8" in macro jobs.
can you explain what is means that?

February 16, 2018, 01:46:18 PM
Reply #9
Offline

David Casella


I thinking that this is a Skill Command for Macro with parameters. I checked in manuals and not founded. In manual has this information.

February 16, 2018, 03:44:11 PM
Reply #10
Offline

asgary64


 yes it is option and active with parameter. I couldn't find it in anywhere. it is in macro jobs for laser sensor. the sensor brand is Metavision.

February 27, 2018, 08:19:15 AM
Reply #11
Offline

potis


do not change anything in the macro commands. also the calibration is done automatically with one point.
read the manual for laser tracking and do several tests to understand it


Share via facebook Share via linkedin Share via pinterest Share via reddit Share via twitter

xx
Alarm codes

Started by dha on Fanuc Robot Forum

5 Replies
3058 Views
Last post July 23, 2016, 09:26:15 AM
by dha
thumbup
All Fanuc Alarm Codes

Started by amir65esf on Fanuc Robot Forum

1 Replies
4106 Views
Last post December 03, 2016, 10:51:43 AM
by amir65esf
xx
A website: Know FANUC alarm codes

Started by linuxsand on Fanuc Robot Forum

28 Replies
44470 Views
Last post May 16, 2019, 01:24:16 PM
by allWar
xx
setting alarm lights to error codes

Started by steimelzackj on Fanuc Robot Forum

3 Replies
2844 Views
Last post September 25, 2013, 01:54:29 AM
by Nation