Threads by ophakala

    1. Title
    2. Replies
    3. Last Reply

    2. Fuse blows in Process I/O board CA after start-up 5

      • ophakala
      • January 11, 2023 at 1:28 PM
    3. Replies
      5
      Views
      4.8k
      5

    4. ophakala

      January 11, 2023 at 1:28 PM

    2. Equipment for KUKA oil change 2

      • ophakala
      • November 25, 2022 at 12:49 PM
    3. Replies
      2
      Views
      3.4k
      2

    4. ophakala

      November 25, 2022 at 12:49 PM

    2. Unable to run subprograms in KUKA KR30 12

      • ophakala
      • November 1, 2022 at 6:55 AM
    3. Replies
      12
      Views
      3.2k
      12

    4. ophakala

      November 1, 2022 at 6:55 AM

    2. Creating system message to make sure that counter is right 2

      • ophakala
      • June 14, 2022 at 11:35 AM
    3. Replies
      2
      Views
      2k
      2

    4. ophakala

      June 14, 2022 at 11:35 AM

    2. SafeOperation: X13 wiring not correct? 2

      • ophakala
      • May 20, 2022 at 3:14 PM
    3. Replies
      2
      Views
      1.7k
      2

    4. ophakala

      May 20, 2022 at 3:14 PM

    2. Information when external axis in safety area 3

      • ophakala
      • May 10, 2022 at 8:33 AM
    3. Replies
      3
      Views
      1.5k
      3

    4. ophakala

      May 10, 2022 at 8:33 AM

    2. KUKA signals that are always on high state and low state? 6

      • ophakala
      • February 21, 2022 at 4:33 PM
    3. Replies
      6
      Views
      2.8k
      6

    4. SkyeFire

      February 21, 2022 at 4:33 PM

    2. base_data gets lost in program 5

      • ophakala
      • January 20, 2022 at 8:53 AM
    3. Replies
      5
      Views
      2.3k
      5

    4. ophakala

      January 20, 2022 at 8:53 AM

    2. KRL templates: Module not found 4

      • ophakala
      • December 12, 2021 at 8:33 PM
    3. Replies
      4
      Views
      4.7k
      4

    4. massula

      December 12, 2021 at 8:33 PM

    2. $Move_enable switched off when robot is not in use 7

      • ophakala
      • October 28, 2021 at 1:44 PM
    3. Replies
      7
      Views
      3k
      7

    4. ophakala

      October 28, 2021 at 1:44 PM

    2. Value assignment inadmissible: Change of $LOAD in interrupt 4

      • ophakala
      • October 18, 2021 at 2:57 PM
    3. Replies
      4
      Views
      2.7k
      4

    4. SkyeFire

      October 18, 2021 at 2:57 PM

    2. KRC4 smartPAD started to act strangely 2

      • ophakala
      • October 18, 2021 at 6:14 PM
    3. Replies
      2
      Views
      1.5k
      2

    4. Ben014

      October 18, 2021 at 6:14 PM

    2. KRC2sr starting issue 9

      • ophakala
      • September 30, 2021 at 4:07 PM
    3. Replies
      9
      Views
      4.2k
      9

    4. MOM

      September 30, 2021 at 4:07 PM

Advertising from our partners