Posts by cian temp

Is FAT
open image.

I have received the PCMCIA to USB card reader, slot the Fanuc card to the reader and I was able to see the contets @ drive E, so the Fanuc Card is ok.
Does that means something is wrong with the Panel board?

Quote from pdl

Have you tried the card slot on the cpu?

That looks like a m410, if so, the controller is under the mechanical unit.

Is a LR mate 200i

Quote from kluk-kluk

Be sure the card is formatted in FAT-16, and NOT in FAT-32

Best to use a card that is 64 MB or less (MB ! not GB)
When you don't have such a card, then erase al the partitions on the card, and then make a new (primary) partition of 32 or 64 MB, and format it in Fat16.
Leave the rest of the card empty.

I don't know if a bigger card or a bigger FAT-16 partition will work, but I have one 2 GB card working with a 32 MB partition on it.

Display More

Quote from pdl

Have you tried the card slot on the cpu?

That looks like a m410, if so, the controller is under the mechanical unit.

Hi kluk- kluk,
"When you don't have such a card, then erase al the partitions on the card, and then make a new (primary) partition of 32 or 64 MB, and format it in Fat16."

The CF card is a 2G size, I will shrink it to 64MB, here is a tutorial on how to shrink a Cf volume to smaller size:

https://timescience.wordpress.…ompact-flash-card-to-2gb/

When shrink to size 64MB I then type this : format fs=fat label=”volumelabel”, is this FAT16?

Load it to R-J3:

see IMG_9668.jpg

Turning Teach Lock On

1) Press TEACH on the playback box.

see IMG_9664

2) Press SELECT.

see IMG_9663

3) Press T-LOCK (F1).

see IMG_ 9662 and 9659

4) Press ENABLE.

when Enable pressed this message shows: IMG_9667

Thanks Tony!
Will try this tomorrow!

Hi guys,
This is what I'm going to do:
1-I have ordered a PCMCIA to USB reader, will plug the Fanuc PCMCIA card to the reader and see if I can read the contents, this is to make sure if the Card is faulty or not.
2- If I use a PCMCIA to CF card adapter what is the max. capacity of CF can I use? 8MB, 16MB, 32MB, 64MB,128MB?

Here is a photo of the controller:
open attachment.

Hi,
I have a LR Mate 200i R-J3 and I tried to load program from a CF to PCMCIA adapter but failed.
To set device I press "Menu"--->"File"---> Util (F5)----> MC---> enter, a message appeared saying MC not detected.
I even tried loading program from the original Fanuc PCMCIA card and also failed, so how do I load program to R-J3 via PCMCIA?

thx,

Thanks, will check the batteries 1st,

thx

The Pendant has no dead man switch, it uses a green button for servo on, see below:

Will look around on FDE,

thx

Hi,
Bought a RV-E2 couple years ago and starting it up now. The power input is 200V bought a transformer step up from 110v to 200v, when switched on the controller starts beeping, the Pro/Alm display flashes 0-3-1-1, can anyone tell me what that means? is there a note for this codes?

Hi,
I'm considering buying a Comau NJ130-2.0 New and add an existing IO cabinet to Comau robot, the IO cabinet was for Kuka KRC2, I think there should not be a problem connecting to a Comau is just what setting needed to be established, correct?. If you wonder why not just call Comau for service, well apparently from what I've heard is that they have to call someone from China to service user in Asia Region (Integrate level), so if that's the case I would rather do it myself if it is not too hard and with the help of this forum.

Mm....code 5390 Servo On abnormal....

Thanks Roboprof.
The original Teach Pendant's screen was faulty cannot see anything on screen, managed to find a spare TP online and replaced the old one.
I'm very surprised it still work after 7 years!
Next thing is how to reset the encoder when all axes lined up, and how to load the program to the controller?

Thx,

Ah, FST key

Hello all,
Is moving now!
Moved the cable around and the servo driver needs to charged, left the controller on for a while to charge.

How do I speed up the manual jog speed?

I have replaced batteries, the low battery is solved, now new alarms :
Code 1360, 1260.
What is PG?

The Motoman Robot is a K3.
It was working when I purchased in year 2010 as used, I left it for a while and would like to start it up again.
The robot was moved around so the axes might have been moved/turned causing the current error. Is there a way to reset the encoder?

Hi,
I have an old Motoman Yasnac MRC currently showing alarm 120, encoder communication error in Japanese, this happens after I Initialise the controller, can any guide me how to solve this error?

Thx

Hi Robotfrenchman,
This is a KRC2 standard.
The KSS 5.4.14 was copied to the SSd drive and installed from desktop, but I had also tried installing it from the CD and both method stuck at "Firewall Settings", but the strange thing is when I power off cabinet then power on I still be able to enter KSS 5.4.14 which is ok, is just the installation does not seem to reach the end page of the installation where it should show a window saying "Installation Complete".

The KSS5.4.14 folder contains a SETUP.exe the only zipped folders are DATA1, DATA2, ENGINE32.