Posts by heri

Quote from axv6l

After register the new arc-caratteristic, the powersource change the led only when robot read the AS istruction

Yes sir, thanks you very much sir

Sent from my vivo 1718 using Tapatalk

Quote from vancanh2000

Have many cause occured fault . This mean command pulse encoder control and signal feedback .may be they are more difference than .you need check connect between motor and Servo amp. and check motor servo and servo amp . If you have new part you can try replace .

thank you sir ,,, ohh sorry just reply for his guidance

Sent from my iPhone using Tapatalk

Quote from vancanh2000

Hi !
You can buy it . From Panasonic robot system or from partner.

Thanks sir

Sent from my iPhone using Tapatalk

please help the robot experts, problem robot panasonic GII TA 1400 ,,,,

Sent from my iPhone using Tapatalk

Hello panasonic robot experts, where can I get DTPS software?

Sent from my iPhone using Tapatalk

After the monitor on the robot set ,, for which in his welding machine it will automatically follow the settings on the monitor what needs to be in the setting itself sir ?? Please help

Sent from my iPhone using Tapatalk

Sent from my iPhone using Tapatalk

Quote from axv6l

you must create e new arc-caratteristic with correct diameter

costant setting----arc weld application......and search the menu for register new caratteristic

Ohhh this is yes sir ,,,,

Sent from my iPhone using Tapatalk

Good night sir...I want to ask if you want to change the diameter of welding wire robot otc daihen how sir?

Sent from my iPhone using Tapatalk

Quote from robotwelder2

Heri,
sorry for the late reply, I have been out of the office for a while.
The only conclusion I can draw is that your I/O board is malfunctioning and needs to be replaced.
regards,
robotwelder2

Yes sir, thanks for the advice ...

Sent from my iPhone using Tapatalk

hallo sir, I have to check in terminal output signal terminal # 1 all I am try one by one but there is no current sir, but the monitor is flame green but rellay yet also connect sir ...

Sent from my iPhone using Tapatalk

Quote from robotwelder2

did you check your 24 Volt power supply?
do you have any voltage at the i/o board output.
It is posible that one output on the i/o board is bad, try using another output, on the picture I see that output 3 is available, try that one.
use a 100mA fuse to protect your i/o board!!

Sent from my iPhone using Tapatalk

Yes sir, I've check the power supplay . And I will try another one output terminal. I would try first sir. Thank you sir

Sent from my iPhone using Tapatalk

yes sir. for such a program I have tried but there are still problems, the output signal that is in use has not been able to rellay sir, to sign on the monitor OUT 1: 01 # 0001 is on the green but not lit rellay sir?

Sent from my C6503 using Tapatalk

Quote from robotwelder2

Dear Heri
I stumbled over this post and looked at the picture of the TP screen;
Three remarks,
1 line 0005 should be MOVEP with welding.
2 line 0008 should be MOVEL without welding.
3 If you are using output #0001 (line 0004) to control a pneumatic device it will possibly not be closed (or opened) as the robot starts welding.
You want to wait for a return message from the pneumatic device or program a delay to give the pneumatic device enough time to close (or open).

Display More

to check cable connection to the output terminal is connect dengen relay clamp jig process, whether it can be run manually from the monitor robot sir, clamp jig when opening or closed sir?

Sent from my C6503 using Tapatalk

I'll try sir ... thanks

Sent from my C6503 using Tapatalk

Yes sir,, thank yoy sir,, robots are here not support weld navigation

Sent from my C6503 using Tapatalk

For setting the output signal if the robot to move the clamp jig processes such as opening, closingor rotating manner in the robot program setting panasonic GIII TA1400 how ya sir?

Sent from my C6503 using Tapatalk

Quote from robotwelder2

In the top menu bar click on set, go down to welding and select the power source you are using.
The first menu item lets you set the wire diameter.
If the diameter you want is not there you will have to buy this option.
If you do not want to buy the option you can use the wrong wire setting, the programmed weld current has to be recalculated because it will be different from the current in the arc start line.
(Make sure the robot is not in automatic mode.)

Thank you sir

Sent from my C6503 using Tapatalk

thank you sir ... it was very helpful ..

Sent from my C6503 using Tapatalk