Thanks i will try 👍😀👍
Posts by angorgus
-
-
strange....o have test this earlier and it work. No same file on my disk campare to yours.
-
yes m94a basic 2.0 version 7
-
yes i can. ersion is V7.....
-
hi i think i have tried to load disk 2 but i get same message to load disk 1. No message its wrong disk. I buy a cpu board on ebay but it not work...😢😢
I think i find the reason for the problem...its a leake roof....i saw water drop fall on topp of cabinet and then in to cabinet..😢😢😢
Maybe its short circuit on some signal.....I rent the area where i have my workshop.....
I will try again o load disk2 or 3
Krg
Göran
-
The problem start after i have swich off the power. I try to restart installation but after the robot have test all installed card i get message to put in disk 1 and then push any key. I try but robot not answer.......
Disk replacement unit work
USB memmory work
-
hi modell is S4 first version. I have not made any changes from switch off to switch on....thats the mystery. Very strange. Maby the memmory card is bad ??
-
I have 2 ABB 1400 and usb work on the other robot. USB have 100 partitioned.
-
hi
I have a new usb replacement unit.
Krg
-
hi
After i switchoff my ABB robot 1400-S4 and restart i can not reload software to the system. The robot test installed cards and then i get question to load disc 1 and then pusch any botton......then nothing happend.
Please someone who have any idea to solve it.....
Krg
GG
-
Hi
I have problem with arcware. When i try to weld i not get analog output for aowirefeed. ao for volt is okey. Some ideas ? When i send ao output from robot it works but not from welddata.
Krg
Goran -
Hi
I need help to scale analog output signal.
I try to start up my ABB 1400 M94 with Migatronic sigma galaxy 500 welding. The welder need 2 analog input from robot m/min (A) and Volt. Both signals from robot is 0-10V. In welddata i write for example 7m/min and should be 200A in welder analog ut from robot 4,0 V
In systemparameters i have fysical max and min, Logic max and min.
How can i scale analog outpot signals ?
Krg
Goran -
Do you have the program yet? Would be nice to see
-
Hello again.
Do you have bullseye?
Can you share the program here? -
Do you have any experience of cmt welding? I wonder how thick you can weld with cmt.
-
What wire and wire size are you using? Gas mixture?
Im using sold wire 1.0 with 92/8 gas. Runs perfect with spray transfer. Have you tried metal cored wire? Im think about to try it. Higher deposition than solid wire and deeper penetration.
-
What thickness are you working with?
I will weld 10mm to 25mmHave you heard about holms?
A swedish snow removal brand.
Great products. I think they robot welding as well. -
In the future i would like to robot weld whole excavator buckets. But then i need a tracking system bucause the buckets are not identical and the gaps may not be the same everywere. Are you tracking with the wire or the gas nozzle? I have seen lazer, but it is pretty expensive... like 10 000 dollar or so. I dont know if its worth it.
-
Ok. Are you the business owner or are you an employee? Im self employed.
Are you using weavedata?
-
Ok. No have not tried robotstudio. I think my robot is to o old. Why do i need robot studio? Offline programming? I had abb here to check so everything was ok, and then i asked him if they use robotstudio for programming and he said no, seldon. Becouse everything has to be so precise irl to accord with computer. Is he wrong? Controlsystem s4