Hi to everyone, I am trying to install the 8.23 version controller cause I need to run some backups on roboguide. The problem is I cant get the FRVC to add.
Do anyone know how to get the version controller?
Controller version 8.23 ROBOGUIDE INSTALL
-
Jose Eduardo Tlalpan -
September 14, 2023 at 11:06 PM -
Thread is Unresolved
-
Nation
September 14, 2023 at 11:34 PM Approved the thread. -
I have versions of software that are built specifically for a certain customer, that isn't a FRVC supported version. However, I can edit the version and Build ID in the backdate.dt file to 'trick' RG into thinking it is a supported version. Not sure about V8.23, but you can give it a try. For example, I would edit V8.23/xx to V8.20/xx:
Your backdate.dt file:
Code
Display More20/11/23 01:57:44 Version: V8.23P/06/None Build ID: V8.23 4/10/2020 1A05B-2500-H551 1A05B-2500-H521 1A05B-2500-J684 1A05B-2500-J765 1A05B-2500-R663 1A05B-2500-J567 1A05B-2500-R784 1A05B-2500-R650 1A05B-2500-R694 1A05B-2500-R809 1A05B-2500-R850 1A05B-2500-J541 1A05B-2500-J878 1A05B-2500-R843 1A05B-2500-J873 1A05B-2500-R848 1A05B-2500-J945 1A05B-2500-J946 1A05B-2500-H746 ZEdit to:
Code
Display More20/11/23 01:57:44 Version: V8.20P/06/None Build ID: V8.20 4/10/2020 1A05B-2500-H551 1A05B-2500-H521 1A05B-2500-J684 1A05B-2500-J765 1A05B-2500-R663 1A05B-2500-J567 1A05B-2500-R784 1A05B-2500-R650 1A05B-2500-R694 1A05B-2500-R809 1A05B-2500-R850 1A05B-2500-J541 1A05B-2500-J878 1A05B-2500-R843 1A05B-2500-J873 1A05B-2500-R848 1A05B-2500-J945 1A05B-2500-J946 1A05B-2500-H746 Z -
Like retobor wrote.
This is the way to go!
This will work or not, and sometimes you'll run into unexpected problems. Because there is a reason V8.23 exists.
Otherwise ask fanuc or the "company" which uses V8.23 for the VRC version.
-
Are you sure it is 8.23 and not 8.13?
I can't seem find any references to a v8.23 anywhere in Fanuc's documentation. However, I do see a separate folder and an additional binary that is located in
\\Program Files (x86)\FANUC\WinOLPC\Versions
I haven't tried this, but you may want to look into \\Program Files (x86)\FANUC\Shared\Off Line\FRVRC\frvirtual.exe.config
You may be able to add a listing for v8.23 that points to the correct resources for v8.20. This is just a WAG, but it might just work.
-
I have versions of software that are built specifically for a certain customer, that isn't a FRVC supported version. However, I can edit the version and Build ID in the backdate.dt file to 'trick' RG into thinking it is a supported version. Not sure about V8.23, but you can give it a try. For example, I would edit V8.23/xx to V8.20/xx:
Your backdate.dt file:
Code
Display More20/11/23 01:57:44 Version: V8.23P/06/None Build ID: V8.23 4/10/2020 1A05B-2500-H551 1A05B-2500-H521 1A05B-2500-J684 1A05B-2500-J765 1A05B-2500-R663 1A05B-2500-J567 1A05B-2500-R784 1A05B-2500-R650 1A05B-2500-R694 1A05B-2500-R809 1A05B-2500-R850 1A05B-2500-J541 1A05B-2500-J878 1A05B-2500-R843 1A05B-2500-J873 1A05B-2500-R848 1A05B-2500-J945 1A05B-2500-J946 1A05B-2500-H746 ZEdit to:
Code
Display More20/11/23 01:57:44 Version: V8.20P/06/None Build ID: V8.20 4/10/2020 1A05B-2500-H551 1A05B-2500-H521 1A05B-2500-J684 1A05B-2500-J765 1A05B-2500-R663 1A05B-2500-J567 1A05B-2500-R784 1A05B-2500-R650 1A05B-2500-R694 1A05B-2500-R809 1A05B-2500-R850 1A05B-2500-J541 1A05B-2500-J878 1A05B-2500-R843 1A05B-2500-J873 1A05B-2500-R848 1A05B-2500-J945 1A05B-2500-J946 1A05B-2500-H746 ZI try this, however the same advertisement appears on RG "The file backup requires version v8.23 wich is not installed. Run de FRVRC setup then try the operation again."
-
What is in C:\Program Files (x86)\FANUC\WinOLPC\Versions? (or wherever you installed RG)
Also, I haven't tried this, but you may be able to edit frvirtual.exe. config to work with v8.23. That file can be found in C:\Program Files (x86)\FANUC\Shared\Off Line\FRVRC
-
Are you sure it is 8.23 and not 8.13?
I can't seem find any references to a v8.23 anywhere in Fanuc's documentation. However, I do see a separate folder and an additional binary that is located in
\\Program Files (x86)\FANUC\WinOLPC\Versions
I haven't tried this, but you may want to look into \\Program Files (x86)\FANUC\Shared\Off Line\FRVRC\frvirtual.exe.config
You may be able to add a listing for v8.23 that points to the correct resources for v8.20. This is just a WAG, but it might just work.
8.23 exist I actually have it in my roboguide. To be honest, not sure how.
-
8.23 exist I actually have it in my roboguide. To be honest, not sure how.
Yes, I have it aswell.
Jose Eduardo Tlalpan have you tried reinstalling RG and selecting FRVRC V8.20 (or any other versions related to V8.2)?
-
Have you tried running it through WinOLPC instead of HandlingTool?
-
Yes, I have it aswell.
Jose Eduardo Tlalpan have you tried reinstalling RG and selecting FRVRC V8.20 (or any other versions related to V8.2)?
Yes, I tried this but in the options I looked FRVRC V8.20, and FRVRC V8.30. I created a robot with 8.20 version with no results. Thank you for your support
-
Have you tried running it through WinOLPC instead of HandlingTool?
Yep, I tried this without succes.
-
Yes, I have it aswell.
Jose Eduardo Tlalpan have you tried reinstalling RG and selecting FRVRC V8.20 (or any other versions related to V8.2)?
I tried it also, I just have the 8.20 and 8.30 versions
Advertising from our partners
