Hello, where can I find the Kuka manual that sent me in the photo
We already told you
Hello, where can I find the Kuka manual that sent me in the photo
We already told you
See
and following posts.
Hello, we call Kuka, responding to the friend's response, Kuka not solurious the problem paying and we are not willing to this for that I am consulted in the forum the documentation could tell me what is the one that would have to come from since it is not understood well and I'm not very on the subject but if they can not help, what I want is that manual would have downloaded for the correct set configuration of the KUKA 2005 edition for Step Software level capture my software version, to add a 7th axis table , Thank you.
Lol . Keep dreaming.
When one wants things done there are two choices - pay someone qualified or do it yourself.
But you do not read, think or follow advice and everything was stated multiple times. You even refuse to communicate properly. Since you are clearly unable to do this, your only option is to hire contractor...
It is very much thanks for the help.
If they saw me said first-time, I had not written to the Claro Forum, they are supposed to be helped when one publish doubts and is shared by knowledge but it would have to be put and forum serves to answer questions and doubts but in the end you have to pay money for it, But in other threads the problem is solved but this thread Nadia wants to help, thank you.
there you go again, writing something incoherent. i don't know where you are but I do not understand your posts. i have tried really hard but cannot decipher what you are trying to say. you were asked several times to try using Google translation services, but you keep ignoring this.
you were offered to move the topic to a forum section with a different language (such as Spanish). you did not accept that.
and you are wrong about people not wanting to help. thread got some 45 messages and that is a lot. But you did not want to work with us. You ask something but then choose to ignore replies. That is not lack of trying from our end, it is you.
btw. there is a name for posting content that is illegible, unrelated and in volume - it is called spamming. so if you want to be taken seriously, try not to spam and try not wasting everyone's time.
everything else was stated several times as well:
- read responses you already got
- read pinned topic READ FIRST
- post full screenshots : also mentioned in READ FIRST
- state correct version : also mentioned in READ FIRST
- read manuals : also mentioned in READ FIRST
- you can get manual from Xpert portal : also mentioned in READ FIRST
So here it is again - KUKA Xpert portal:
And btw if you think the above text boxes are screenshots. They are not. They are links you can follow by clicking on them. Hence by clicking on them the whole content is revealed and can be studied by you.
Worth having commented where we have been left if vams per step and can help me with the error that I have on the screen when the mocked fault was added we have this error that passes and please step by step can indicate how to act and mall to solve the Problem Step Screen capture in groin as they ask me for change Language in Kuka HMI and step photo, thank you.
diference between XML / RDC data and machine
This is what I wanted to do, let's try it understand it now
">
Let's check if it does not work, thank you.
Hello, we have tried and the messages do not do not take away where we can check and look for the error.
Step Capture with English HMI Leo the texts, thank you.
">
Thank you we are going to look with a partner who pilot Kuka and we tell him how to proceed, thank you.
Machine data for external axis probably not correct. Correct them and try again. Get external axis documentation and setup anew with it.
maybe wrong motor or servo drive selected, or gain too high, or brake does not release...
Hello, we have tried to move the motor without current and the engine does not turn the photo with a key, we have tried to move it ManualMenet and N turns look like locked .. I repeat without current ..
I understand that these motors are only unlocked with current and when it is with current the motor brake is entered and because we now have this failure in the engine, they spoke to me in a previous post to put a relay or something like that we have to put it and how it is put or some scheme that has someone who can tell me as if this is why it is that the engine is damaged, thank you.
I wanted to consult how to do this which is a problem is surely that it is not done what the comment I did not do on this topic since the driver does not have SMB.
And he told us this ..
and correctly wire E1 brake to X12 of PM600
X12 already uses two wires (pins 1, 2) for robot brakes.
you need to add contacts 3 and 4 for external axes (channel 21)
also need to add 2A circuit breaker and run positive wire couple times through new toroid. this is needed to suppress spikes when brake is applied (current through brake turned off).
There is some scheme or plan of how to do it and pieces that I have to ride to deactivate the brake and solve the problem that I have, thank you very much ..
This
also need to add 2A circuit breaker and run positive wire couple times through new toroid. this is needed to suppress spikes when brake is applied (current through brake turned off).
If i recall correctly it goes something like this. Channel20 is meant for robot. For external Axis use PMCHANNEL 21. you need to duplicate circuit that already exists for robot brake. As you can see, right side is what you need to add and it is very much the same as your robot schematics already shows for the robot brake. but instead of X20, this will be wired to X7.1.
This is standard version when E1 servo drive is without SBM2. Wiring of SBM2 is completely different.