Hello everyone,
I am new with the robotics and I wanted to know how to connect a Fanuc Robot and Siemens PLC 1500
Thank you very much
Fanuc Robot and Siemens PLC 1500
- MoEL
- Thread is marked as Resolved.
-
You need to buy Profinet card and Profinet software from Fanuc.
-
You need to buy Profinet card and Profinet software from Fanuc.
How can I check if there is already a card and soft installed?
Thank you
PS: When I go Menu > IO > next, I have Profinet PFN-TP-CT
Does that mean that I can connect the robot to PLC by Profinet?
-
You can check what options you have installed by pressing MENU > 0 > 4: STATUS > Version ID > Softkey F3 CONFIG. There will be a list of every option installed.
-
You can check what options you have installed by pressing MENU > 0 > 4: STATUS > Version ID > Softkey F3 CONFIG. There will be a list of every option installed.
When there, how to find out wich comunication protocol is installed?
Thanks
Edit: I have "Dual Chan. Profinet" and PROFINET CP16XX FW, Is that what I need?
Thank you
-
Yes. But configuration is a bit fiddly.
-
Yes. But configuration is a bit fiddly.
My bad,
Do you have any doc or advise?
Thanks
-
You can get the documentation from Fanuc customer support. Register to https://www.fanucamerica.com/support/robot/cc-registration or https://my.fanuc.eu/.
-
You can get the documentation from Fanuc customer support. Register to https://www.fanucamerica.com/support/robot/cc-registration or https://my.fanuc.eu/.
I am already redistred, and account validated by Fanuc,
I can see documents, but I am not able to find the right doc for this
Could you give me the doc name please?
Thanks
-
It is B-82864EN/06
-
Yes. But configuration is a bit fiddly.
I have a doc to configure it, but I don't really now if I have Profinet Software&Hardware installed?
How can I check if I have these?
Thank you
-
I have a doc to configure it, but I don't really now if I have Profinet Software&Hardware installed?
How can I check if I have these?
Thank you
Its been a while for me but , do you have a profinet option on Menu > (5) I/O > (0) Next and here you should see PROFINET.
Its better if you look in the software info as RockemSockem told you.
-
Edit: I have "Dual Chan. Profinet" and PROFINET CP16XX FW, Is that what I need?
Here you stated that you have cp16xx, now again you don't know?
Post a picture of your controller, and the version IDs.
-
Here you stated that you have cp16xx, now again you don't know?
Post a picture of your controller, and the version IDs.
Yes, I have that options, but I don't see the CP16xx when I open the cabinet, so it's a bit confusing.
Here are the pictures
Thanks
-
You have the Molex option (Dual Channel Profinet, R834). Option J744 is just the firmware of the Siemens CP16xx located on the controller.
-
The other picture shows the Molex card. You will find the steps for configuration in the PROFINET manual. See your other topic for information about the GSDML file. I already answered this question in the second thread.
-
The other picture shows the Molex card. You will find the steps for configuration in the PROFINET manual. See your other topic for information about the GSDML file. I already answered this question in the second thread.
Thank you,
I read you answer there, but I have no idea in how to customize and GSDML.
thanks
-
You don't need to create your own GSDML file for the Molex option. This is only required for the Siemens CP16xx.
-
You don't need to create your own GSDML file for the Molex option. This is only required for the Siemens CP16xx.
Okay, thanks,
Where can I find the right GSDML?
Advertising from our partners
