Panasonic Training?

Look into this. MWA is the source for Panasonic training
https://reg.abcsignup.com/view/view_mont…&aid=MEM&wp=264

Good day sir .... for setting counter in the robot panasonic GII or GIII let appear on the monitor how ya do ....?

program : ....
SET LI001 = 0 (Set 0 to variable LI001)
SET GR002 = 0 (Set 0 to variable GR001)
INC LI001 (Increment the value of LI001 by 1)
ADD GR001, 2 (Add 2 to variable GR001)
....

monitor : View --> Display change --> Display variable --> Integer (or Real)

change value : Set --> Variable --> Integer (or Real)

Thank you very much sir on his direction ....

Sent from my ASUS_Z00RD using Tapatalk

good afternoon sir yes sir ... ohh .... sorry sir I ask again ... that make the program create a button how sir? for panasonic GII. because if I change its operation to continou, operators quickly lose the same robot guidance please sir ...

Sent from my ASUS_Z00RD using Tapatalk

connect opetation button to I/O terminals User-IN001.
at the begin of program, add : WAIT_IP I1#(001) = ON

Thank you very much sir, for helping

Sent from my ASUS_Z00RD using Tapatalk

good evening sir, to counter setup I have tried but they failed to create .program: .... SET LI001 = 0 (Sets 0 to variable LI001) SET GR002 = 0 (Sets 0 to variable GR001) LI001 INC (Increment the value of LI001 by 1) ADD GR001, 2 (Add 2 to variable GR001) .... monitor: View -> Display change -> Display variables -> Integer (or Real) change value: Set -> variable - -> Integer (or Real), for the program for this counter setting input into the program at the beginning or at the end sir. I should have asked for an example of the program to enter sir.

Sent from my ASUS_Z00RD using Tapatalk

if to counter can already appear sir but the counter is not running although robots have completed the process still rates still at 0

Sent from my ASUS_Z00RD using Tapatalk

Ok, GR001 = counter

at the end of program : ADD GR001, 1 (add 1 to counter)

monitor : View --> Display change --> Display variable --> Real

to reset the counter : Set --> Variable --> Real

thanks sir ..... I'll try again.[emoji1]

Sent from my ASUS_Z00RD using Tapatalk

Hello sir .... thanks for the guidance that has been given to me , everything has been running smoothly . There is one more thing I want to ask sir , if I want to add additional devices such as PLC 's , do I need to register for a robotic device before the signal I/O I plug in one program .... sir ? ... Excuse me sir if I ask many questions ....

these status input/output and user input/output are ready to use

Thank you sir , if the OTC or protecting nachi right to know the level of user or beginer , experts , specialists and integrators to pasword.
What in panasonic also there like that or just passing user id that alone sir for robot models in the password .... ?

Sent from my ASUS_Z00RD using Tapatalk

Only users of the system administrator level can set, change and delete all parameters.

Thank you sir ... for his guidance , I hope that the father of science has also increased and growing , amen ....

Sent from my ASUS_Z00RD using Tapatalk

Hi , there are some problems with my Panasonic robot AW005cl after the relocation Recently ,
I have a panarobo AW-005cl. When i turn on servo. Robot display error : " A6110 encoder batt Err0001".
Please help me! Thanks

Quote from achencan

Ok, GR001 = counter

at the end of program : ADD GR001, 1 (add 1 to counter)

monitor : View --> Display change --> Display variable --> Real

to reset the counter : Set --> Variable --> Real

hello sir .... I want to ask panasonic robot GII often Alarm A4010 safety warnings holder when the gun or the robot head not hit anything .. if there is a problem in the sensor or there are other constraints yes sir ...? yes sir please help ... thanks in advance ...[emoji4]

Sent from my ASUS_Z00RD using Tapatalk

A4010 xxxxxx ------- what error message you have ?