1. Home
    1. Dashboard
    2. Search
  2. Forum
    1. Unresolved Threads
    2. Members
      1. Recent Activities
      2. Users Online
      3. Team Members
      4. Search Members
      5. Trophys
  3. Articles
  4. Blog
  5. Videos
  6. Jobs
  7. Shop
    1. Orders
  • Login or register
  • Search
This Thread
  • Everywhere
  • This Thread
  • This Forum
  • Articles
  • Pages
  • Forum
  • Blog Articles
  • Products
  • More Options
  1. Robotforum - Support and discussion community for industrial robots and cobots
  2. Forum
  3. Industrial Robot Support and Discussion Center
  4. Stäubli & Bosch Robot Forum
Your browser does not support videos RoboDK Software for simulation and programming
Visit our Mainsponsor
IRBCAM
Robotics Channel
Robotics Training
Advertise in robotics
Sponsored Ads

TCP remote maintenance tool

  • chocobo_ff
  • May 1, 2014 at 3:28 AM
  • Thread is Resolved
  • chocobo_ff
    Trophies
    3
    Posts
    32
    • May 1, 2014 at 3:28 AM
    • #1

    We are having some issues with our CS8C controller, where the system is not booting up properly. When the power is switched on, the MCP is stuck at the Staubli logo page, and doesn't go into the menus after a minute or two. I've read in the SRS manual that there is a TCP remote maintenance tool, but there is no information on what software/configuration is required to access this, does someone have this information?

    For those interested, these are the error indicators on the controller:


      • RSI: the three LEDs for power status (D49, D50 and D52): D49 and D50 are on, D52 is off (5V from STARC board). We checked the power LEDs inside STARC (1.2V, 1.4V, 2.5V, 3.3V and 5V), all 5 LEDs are on, indicating that there is in fact 5V at the STARC board. 7-segment display has a flashing ‘E.’ (~1 second).

      • STARC: the 5 LEDs (A-E): D and E are on (orange), A and B are flashing slowly (red), C is off.

    Any suggestions/recommendations would be much appreciated.

  • klausi
    Reactions Received
    8
    Trophies
    3
    Posts
    37
    • May 5, 2014 at 9:08 AM
    • #2

    Hi

    You may try to connect to COM1 115200,8N1 with a terminal emulation software like hyperterminal and check what is output during the boot sequence.

    If the Flash disk is not completely damaged, you should be able to boot via a USB stick. The way to proceed depends on the CPU type installed in your controler. The best solution is to contact your stäubli local support team.

  • bruceboty
    Trophies
    2
    Posts
    5
    • May 11, 2014 at 9:04 AM
    • #3

    I assumed you knew the IP address of CS8C, for example: 192.168.1.11 for J204, set your PC's IP: 192.168.1.12
    1. open your command windows
    2. ping 192.168.1.12 -t
    3. if you got ping from the controller, reboot it again, but run telnet 192.168.1.12 then you can trace the real issue of the boot problem
    4. if the ping doesn't work, the only way you can do is created a bootable usbkey to reinstall the system.

  • painful_staubli
    Reactions Received
    3
    Trophies
    1
    Posts
    44
    • July 26, 2023 at 1:40 AM
    • #4

    bruceboty could you please share the URL to download the files to create an ISO image with Balena Etcher? I got stock with this issue.

Advertising from our partners

IRBCAM
Robotics Channel
Robotics Training
Advertise in robotics
Advertise in Robotics
Advertise in Robotics

Job Postings

  • Anyware Robotics is hiring!

    yzhou377 February 23, 2025 at 4:54 AM
  • How to see your Job Posting (search or recruit) here in Robot-Forum.com

    Werner Hampel November 18, 2021 at 3:44 PM
Your browser does not support videos RoboDK Software for simulation and programming

Tag Cloud

  • abb
  • Backup
  • calibration
  • Communication
  • CRX
  • DCS
  • dx100
  • dx200
  • error
  • Ethernet
  • Ethernet IP
  • external axis
  • Fanuc
  • help
  • hmi
  • I/O
  • irc5
  • IRVIsion
  • karel
  • kawasaki
  • KRC2
  • KRC4
  • KRC 4
  • KRL
  • KUKA
  • motoman
  • Offset
  • PLC
  • PROFINET
  • Program
  • Programming
  • RAPID
  • robodk
  • roboguide
  • robot
  • robotstudio
  • RSI
  • safety
  • Siemens
  • simulation
  • SPEED
  • staubli
  • tcp
  • TCP/IP
  • teach pendant
  • vision
  • Welding
  • workvisual
  • yaskawa
  • YRC1000

Thread Tag Cloud

  • abb
  • Backup
  • calibration
  • Communication
  • CRX
  • DCS
  • dx100
  • dx200
  • error
  • Ethernet
  • Ethernet IP
  • external axis
  • Fanuc
  • help
  • hmi
  • I/O
  • irc5
  • IRVIsion
  • karel
  • kawasaki
  • KRC2
  • KRC4
  • KRC 4
  • KRL
  • KUKA
  • motoman
  • Offset
  • PLC
  • PROFINET
  • Program
  • Programming
  • RAPID
  • robodk
  • roboguide
  • robot
  • robotstudio
  • RSI
  • safety
  • Siemens
  • simulation
  • SPEED
  • staubli
  • tcp
  • TCP/IP
  • teach pendant
  • vision
  • Welding
  • workvisual
  • yaskawa
  • YRC1000

Users Viewing This Thread

  • 2 Guests
  1. Privacy Policy
  2. Legal Notice
Powered by WoltLab Suite™
As a registered Member:
* You will see no Google advertising
* You can translate posts into your local language
* You can ask questions or help the community with your knowledge
* You can thank the authors for their help
* You can receive notifications of replies or new topics on request
* We do not sell your data - we promise

JOIN OUR GREAT ROBOTICS COMMUNITY.
Don’t have an account yet? Register yourself now and be a part of our community!
Register Yourself Lost Password
Robotforum - Support and discussion community for industrial robots and cobots in the WSC-Connect App on Google Play
Robotforum - Support and discussion community for industrial robots and cobots in the WSC-Connect App on the App Store
Download