January 18, 2019, 03:46:05 AM
Robotforum | Industrial Robots Community

 Controllo AD


Author Topic:  Controllo AD  (Read 681 times)

0 Members and 1 Guest are viewing this topic.

October 15, 2018, 09:20:26 AM
Read 681 times
Offline

dolomix


Ciao, dopo mesi di interruzione ho riacceso il mio robot saldatore, e riscontrato errori alle batterie delle schede 9ZA e sostituite, e 1FG e sostituita ora il display segnala errore 955 non presente a manuale con la dicitura "Sum check error of external axis control power" qualcuno ha già affrontato il problema? Grazie

Linkback: https://www.robot-forum.com/robotforum/index.php?topic=29140.0
  • Like    Thanks

Today at 03:46:05 AM
Reply #1

Advertisement

Guest

October 15, 2018, 09:48:54 AM
Reply #1
Offline

dolomix



Hello, after months of interruption I have my robot welder, and I tried the batteries of the 9ZA cards and replaced, and 1FG and replaced now the display indicates error 955 does not present a manual with the words "someone has already faced the problem?
  • Like    Thanks

October 16, 2018, 11:32:04 AM
Reply #2
Offline

Nzhuhu


Hello Dolomix,

If I am not mistake the Error 0955 is Sun Check Error of External Axis control Parameter.
Kawasaki also recommend to save all parameters from Robot Controller on Floppy Disk or any kind of external Storage which can work on your Controller.
Also they make very clear Caution that when you are trying to change the Battery, you must do it under 1 hour time.

I will try to read my Manual carefully to spot which page to help us solve the Error 0955.
  • Like    Thanks

October 16, 2018, 01:58:41 PM
Reply #3
Offline

dolomix


Many thanks NZHUHU, on my manual none, and I can not move robots to reposition it, I have tried all the buttons of the teach and console but nothing the motor is not powered. Thanks to the availability.
  • Like    Thanks

October 16, 2018, 07:07:40 PM
Reply #4
Offline

kwakisaki

Global Moderator
Welcome to the forum........... :beerchug:

Checksum Error can be cleared if you access Aux 78.
- You can also enter the command CHSUM on the screen and enter 1.

This should allow you to clear the check sum error.
If it returns, you may need to load in data AS/SV and a possible backup (but let us know if the above works).
  • Like    Thanks

October 17, 2018, 01:38:30 PM
Reply #5
Offline

dolomix


I'm honored to talk to Kwakisaki, already made access to aux 78 and restored factory data with back-up floppies and it is still not possible to give power to the engines, perhaps the card on the arm (1FG) lost data but how to reinsert them?https://www.robot-forum.com/robotforum/Smileys/robotforum/flower.gif
  • Like    Thanks

October 17, 2018, 02:49:42 PM
Reply #6
Offline

kwakisaki

Global Moderator
Sorry to hear that, can you post a picture of your screen/display and include any additional information you may have - eg is the error light permanently on.
You mention about not possible to put power to the engines (I assume Motor Power is not possible).
Either Safety circuit or Permanent error is common to prevent motor power, so can you provide further details?
  • Like    Thanks

Today at 03:46:05 AM
Reply #7

Advertisement

Guest

October 22, 2018, 12:12:29 PM
Reply #7
Offline

dolomix


Hi done photo display I hope it is clear I tried to cacellare error but nothing ... I hope the manual of Nzhuhu give complete answer ... From the Alps a white greeting.
  • Like    Thanks

October 22, 2018, 05:46:26 PM
Reply #8
Offline

kwakisaki

Global Moderator
Hmmm, this could be difficult to recover.

The Check Sum is error is referring to an external axis.
I think with dipswitch settings, this is activated and backup data if contain external axis data and 'clean initialisation' will cause loss of external axis parameter settings, so separate file maybe required.

1. Do you have an external axis fitted - ie servo gun, rotary positioner.
2. If you have, do you have any other information on your floppies like a file that ends with extension .mot
  • Like    Thanks

October 23, 2018, 09:28:45 AM
Reply #9
Offline

dolomix


 :wallbash:
Right, I have a rotary positioner but not a .mot file
On floppy I have a cpuerr .bsv file but I can not read it and I do not know where it goes?
  • Like    Thanks

October 23, 2018, 09:32:58 PM
Reply #10
Offline

kwakisaki

Global Moderator
I think the file you refer to maybe an old file due to having a 'b' in extension, I think from memory software (servo) extension is .sv0.

I think the only possible solution is to contact KHI (or your local Kawasaki distributor) and see if they can supply correct files for external axis.
- Due to age of robot, maybe very difficult to obtain now unless a user here has these files available.

Do you have other systems available, or is this the only one you have access to?
  • Like    Thanks


Share via facebook Share via linkedin Share via pinterest Share via reddit Share via twitter