KUKA Robot Forum

Help, support and discussions-Forum for KUKA robots with RCM2, RCM3, KR C1, KR C2, KR C3, KR C4, VKR C1, VKR C2, VKR C4 and KRC ROBOTstar controller.
All kinematics, hardware and software like KRL

    1. krc2 profibus dp

      • javaman
    2. Replies
      0
      Views
      52
    1. Milling spindle on/off during Powermill krl program execution in KSS 5.6.12 26

      • Gocea
    2. Replies
      26
      Views
      654
      26
    3. panic mode

    1. KUKA Controller Cannot start 29

      • jibesh
    2. Replies
      29
      Views
      21k
      29
    3. acili17

    1. Virtual Commissioning with Tecnomatix-Siemens Process Simulate 1

      • Automation
    2. Replies
      1
      Views
      26
      1
    3. massula

    1. Kuka krc1 9

      • idrisssoft
    2. Replies
      9
      Views
      198
      9
    3. idrisssoft

    1. KRC2 ArcTech welding issues 5

      • Arrari
    2. Replies
      5
      Views
      354
      5
    3. fluke

    1. Overwrite Problem on Backups 6

      • MertOzer
    2. Replies
      6
      Views
      195
      6
    3. Fubini

    1. Oversized servo configuration on brand new KRC4? Is it possible? 2

      • RAS-Skordos GR
    2. Replies
      2
      Views
      233
      2
    3. MOM

    1. Approximating/branching Spline motions 27

      • SkyeFire
    2. Replies
      27
      Views
      7.2k
      27
    3. Turugor

    1. KUKA KR150 R2700-2 KRC4 - Points offset through HMI Easy 2

      • Dave11
    2. Replies
      2
      Views
      176
      2
    3. Dave11

    1. Handle system errors in Ext mode 4

      • Agustin Costa
    2. Replies
      4
      Views
      179
      4
    3. Agustin Costa

    1. kuka ks00404 11

      • isai blanco
    2. Replies
      11
      Views
      340
      11
    3. panic mode

    1. UPGRADE KRC2 Software V4.1.7 to Software V5.4.14 12

      • Eric70300
    2. Replies
      12
      Views
      272
      12
    3. Eric70300

    1. Machine data do not match robot type 13

      • Ayoub
    2. Replies
      13
      Views
      6.8k
      13
    3. hermann

    1. Need "Open Appplicator" Signal on Dry Run 5

      • MertOzer
    2. Replies
      5
      Views
      163
      5
    3. MertOzer

    1. Boot stops in Kuka cross 40

      • Leon
      • Leon
    2. Replies
      40
      Views
      12k
      40
    3. sasi1922

    1. Linear 2-axis XY system configuration in Catalog Editor 1

      • Turugor
    2. Replies
      1
      Views
      86
      1
    3. panic mode

    1. KUKA VIRUTAL KCP. 7

      • szkyrp
    2. Replies
      7
      Views
      160
      7
    3. MOM

    1. KUKA KRC4 error "Current Overload after 60.0 s (A2)(Holding Current)" 19

      • nikhilpotdar15
    2. Replies
      19
      Views
      7.4k
      19
    3. panic mode

    1. Machine MADA data do not match robot type 19

      • Valmir
    2. Replies
      19
      Views
      794
      19
    3. MOM

Display Options

Please start a new thread only after using the search function to see if there is already an existing thread which addresses your question.
If you find a related thread, post your question there instead of starting a new thread.
Doing so helps to keep the clutter down and makes the forums more navigable.
Please give additional information regarding controller, robot arm and software versions with your question.

This is not an official Kuka Robotics support forum. Please do not post copyrighted manuals or licensed software downloads.