Stäubli & Bosch Robot Forum

The very fast and highly accurate Swiss robot speaks many languages.

Mark All as Read

    2. Most efficient way to move the robot through many points with minimal commands, cobot TX2 90 6

      • Vi NTT
    3. Replies
      6
      Views
      803
      6

    4. Vi NTT

    2. Staubli saving/reloading application without a pendant 5

      • PRISMA
    3. Replies
      5
      Views
      685
      5

    4. PRISMA

    2. STaubli CS9 How to read the position of the robot continously with a siemens Profinet PLC 3

      • danielangos
    3. Replies
      3
      Views
      684
      3

    4. Psyril

    2. Side loading individual files to prevent freezing

      • painful_staubli
    3. Replies
      0
      Views
      738

    2. 2011 Staubli RX160 - which controller - CS8? 8

      • HeyItsMe
    3. Replies
      8
      Views
      1.1k
      8

    4. HeyItsMe

    2. Message <0x007> DRIVE-SensorNotReady: The Starc bus could not communicate with sensor because the bus for axis 1 is not synchronous [SYNCHRO bit]. 3

      • painful_staubli
    3. Replies
      3
      Views
      1k
      3

    4. painful_staubli

    2. Error USIB Safety Stop J100 Staubli 4

      • Vi NTT
    3. Replies
      4
      Views
      1.1k
      4

    4. Vi NTT

    2. How to know arm tuning if it is different from arm.cfx file?

      • aknezevi.proton
    3. Replies
      0
      Views
      932

    2. Change mounting type on controller 1

      • aknezevi.proton
    3. Replies
      1
      Views
      997
      1

    4. Psyril

    2. How to know hardware available on the controller? 3

      • aknezevi.proton
    3. Replies
      3
      Views
      1.4k
      3

    4. aknezevi.proton

    2. Val 3 appro() function 9

      • WolfgangE
    3. Replies
      9
      Views
      2.3k
      9

    4. Galet

    2. [SOLVED] Problem with setting up Stäubli CS8 with RX60B - L 6

      • ondra1808
    3. Replies
      6
      Views
      2.2k
      6

    4. klausi

    2. Changed format of J206_SyCon_ENI.xml file to indent. 4

      • mil3k
    3. Replies
      4
      Views
      1.9k
      4

    4. Galet

    2. I/O Physical - Staubli TX2_40 - Gripper 2

      • ananas153
    3. Replies
      2
      Views
      2k
      2

    4. ananas153

    2. How can I execute? 1

      • glsmith86
    3. Replies
      1
      Views
      1.9k
      1

    4. Psyril

    2. Using Rpi as emulator to replace floppy drive in RX130 CS7 10

      • jmouw28
    3. Replies
      10
      Views
      2.3k
      10

    4. jmouw28

    2. ESI file for EtherCAT safety for "CS9 EtherCAT slave with FSoE on J207/J208" robot on twincat (ESI == XML configuration file) 2

      • robotecnik
    3. Replies
      2
      Views
      1.9k
      2

    4. Galet

    2. What licence is needed to connect SRS2019 with external devices? 3

      • mil3k
    3. Replies
      3
      Views
      1.3k
      3

    4. Galet

    2. How to read a virtual signal from a tool in SRS2019 (eg.: "diPartDetected")? 6

      • mil3k
    3. Replies
      6
      Views
      1.7k
      6

    4. mil3k

    2. CS8C error codes - U and in ARPS 12v2 not showing 1

      • Sarath Kumar
    3. Replies
      1
      Views
      1.4k
      1

    4. klausi

Display Options

Please start a new thread only after using the search function to see if there is already an existing thread which addresses your question.
If you find a related thread, post your question there instead of starting a new thread.
Doing so helps to keep the clutter down and makes the forums more navigable.
Please give additional information regarding controller, robot arm and software versions with your question.

This is not an official Staubli or Bosch Robotics support forum. Please do not post copyrighted manuals or licensed software downloads.

Advertising from our partners